Wayne-Dalton 347610 End Bearing Brackets, Center Bracket, Torsion Spring Assembly

adjusted for each side.

Starting on the left hand side, vertically align the top section of the door with the lower sec- tions. Maintaining the top fixture(s) position, tighten the 1/4”-20 flange hex nuts or 1/4”-20 x 1-3/8” bolts and or 1/4”-14 x 1” lag screws to secure the top fixture(s) to the top section. Repeat for other side

	Flag angle	Left hand top fixture(s)
	Top	(2) 1/4” - 20 Flange hex nuts or
	rail
		(2) 1/4” - 20 x 1-3/8” bolts
Horizontal		(2) 1/4” - 14 x 1”
		Lag screws
tracks	Track roller
		Top section

16	End Bearing Brackets
	Tools: Step ladder, Power drill, 7/16” Socket driver

NOTE: Right and left hand is always determined from inside the garage looking out. End bearing brackets are right and left hand.

Identify the end bearing brackets supplied with your door.

Align the bottom edge of left end bearing bracket with the top edge of the flag angle. Main- taining this alignment, also align the right edge of the end bearing bracket with the right edge of the flag angle.

Secure the end bearing bracket to the jamb using (3) 5/16” x 1-5/8” lag screws, as shown. Repeat same process for the other side.

	Left end bearing	Left end bearing
	bracket	bracket
		(3) 5/16” x 1-5/8”
		Lag screws
	Bottom
Top edge	edge
of flag
angle
	Top	Top
	section	section

Position the left hand end bearing bracket up against the jamb and the horizontal track, as shown. Fasten the left hand end bearing bracket to the horizontal track with (1) 3/8”-16 x 3/4” truss head bolt and (1) 3/8”-16 nut. Secure the left hand end bearing bracket to the jamb using (3) 5/16” x 1-5/8” lag screws. Repeat same process for the other side.

Left end bearing	(3) 5/16” x 1-5/8”	Left end bearing	bracket
bracket	Lag screws	(1) 3/8”-16 x 3/4”
		Truss head bolt
	(1) 3/8”-16
	Hex nut		Upper
			slot
	Horizontal	Horizontal
	track	track

17	Center Bracket
	Tools: Step ladder, Power drill, 7/16” Socket driver, 1/4” Torx bit, Level,

NOTE: Refer to the Package Contents and or Parts Breakdown to determine if your door came with a coupler assembly.

NOTE: If your door came with a coupler assembly, the mounting surface needs to be a mini- mum of 17” wide. The (2) center bearing brackets will need to be spaced 12” to 14” apart, at the center of the door, as shown.

Locate the center of the door.

If your door did not come with a coupler: Mark a vertical pencil line on the mounting surface above the door, at the center.

If your door did come with a coupler: Mark a vertical pencil line on the mounting surface above the door, at the center. Split the difference up and position the (2) center bearing brackets apart from each other. Mark two vertical pencil lines, one for each center bearing bracket onto the mounting surface above the door.

Measure from the center of the bearing, in one of the end bearing brackets, downwards, to the top the door. Using that measurement, measure that distance upwards from the top of the door to the mounting surface and mark a horizontal pencil line which intersects the vertical pencil line(s). Align the edge of the center bracket(s) with the vertical pencil line and the center of the center bracket(s) with the horizontal pencil line; this is to ensure the torsion shaft is level between the center and end bearing brackets.

Attach the center bracket(s) to the mounting surface, using (2) 5/16” x 1-5/8” lag screws and

(1) 5/16” x 2” tamper-resistant lag screw.

IMPORTANT: Use a 5/16” x 1-5/8” tamper-resistant lag screw instead of the 5/16” x 2” tamper-resistant lag screw if mounting surface is mounted over masonry. Tamper-resistant lag screw must be attached through the bottom hole of the center bracket(s).

Center of typical	Mounting	Typical	Center of typical
end bearing bracket	surface	center	end bearing bracket
		bracket
	Horizontal	Vertical
		line
	line

Equal distance from top of door section to horizontal line

Mounting	Center bracket		Vertical	Mounting
surface	bushing assembly		line	surface
Vertical	(2) 5/16” x 1-5/8”		(2) 5/16” x 1-5/8”
	Lag screws			Lag screws
line
Horizontal
line
				Center
				bearing
			Horizontal	bracket
			line	assembly
(1) 5/16” X 2” or (1) 5/16” x 1-5/8” Tamper-resistant lag screw
Mounting surface	Center	†	Vertical line
(17” Minimum)	of
	door
Vertical
line			(2) 5/16” x 1-5/8”
(2) 5/16” x 1-5/8”				Lag screws
Lag screws

Horizontal		† (2) Center bearing
line
	(1) 5/16” X 2” or (1) 5/16”	brackets spaced 6” to 7”
	x 1-5/8” Tamper-resistant	apart from the center of
	lag screw	the door.

18	Torsion Spring Assembly
	Tools: Step Ladder

NOTE: Refer to the Package Contents and or Parts Breakdown to determine if your door came with a coupler assembly.

IMPORTANT: Right and left hand is always determined from inside the building looking out.

IMPORTANT: On single spring applications, only a right hand wound (red wind- ing cone), which goes on the RIGHT HAND SIDE is required.

NOTE: Identify the torsion springs provided as either right hand wound (red winding cone), which goes on the RIGHT HAND SIDE or left hand wound (black winding cone), which goes on the LEFT HAND SIDE.

For Doors without Coupler Assembly:

Facing the inside of the door lay the torsion shaft on the floor. Lay the torsion spring with the black winding cone and the red cable drum at the left end of the torsion shaft. Lay the torsion spring with the red winding cone and the black cable drum at the right end of the torsion shaft.

NOTE: The set screws used on all torsion winding cones and cable drums are now colored red. DO NOT identify right and left hand by the set screw color.

Slide the center bracket bushing or center bearing onto the torsion shaft followed by the torsion springs.

12

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com