Wayne-Dalton 347610 installation instructions Set Collars, Tools Vice Clamps

Center bearing bracket(s)

Coupler

assembly

Center bearing inside

torsion spring

Torsion

spring

Center

bearing

Torsion

keyed

shaft

Center bearing brackets Coupler assembly

Set screws

Torsion

keyedLock nuts shaft

(3) 3/8” - 16 x 1-3/4”

hex head screws

	(3) 3/8” - 16
	nylon hex lock
Torsion	nuts
keyed
shaft
	Coupler
	halves

(2) 3/8”-16 Nuts	Typical center bracket
	assembly

Left hand end	Torsion spring
bearing bracket
Key	Left hand
	cable drum

Torsion spring

Stationary spring cone

Torsion spring

(2)3/8”-16 x 1-1/2” Hex head bolts

Torsion
keyed
shaft
21	Set Collars
	Tools: Step Ladder, 3/8” Wrench

NOTE: If your door did not come with set collars, then skip this step.

Center bearing brackets Coupler assembly

Set screws

Torsion

keyedLock nuts shaft

(3) 3/8” - 16 x 1-3/4”

hex head screws

	(3) 3/8” - 16
	nylon hex lock
Torsion	nuts
keyed
shaft
	Coupler
	halves

Slide each of the set collars up against the inside surface of the end bearing brackets, with the set screw facing directly away from the header. Tighten the set screw in each of the set collars to the torsion shaft to 14-15 ft. lbs. of torque (once set screw contacts the shaft, tighten set screw one full turn).

IMPORTANT: Prior to tightening the set screws in the set collars, avoid plac- ing the set screws in the keyways of torsion keyed shaft(s).

End	Right	End bearing
bearing	hand
		bracket
bracket	cable
	drum

20	Counterbalance Lift Cables
	Tools: Step Ladder, Locking Pliers, 3/8” Wrench

Starting on the left hand side, thread the counterbalance lift cable up and around the front side of the left hand cable drum.

IMPORTANT: Verify that there are no counterbalance lift cable obstructions.

Hook the counterbalance lift cable into the left hand cable drum. Starting on the left hand side, slide the left hand cable drum onto the torsion shaft and up against the left hand end bearing bracket. Counterbalance lift cable should provide a minimum of 1/2 pre-wrap on the cable drum. Tighten the (2) set screws in the cable drum to 14-15 ft. lbs. of torque (once set screws contact the shaft, tighten set screws one full turn).

NOTE: For doors with a torsion keyed shaft, insert (1) key shaft into the slot of both the cable drum and the slot in the torsion keyed shaft, as shown.

Rotate the left hand drum and torsion shaft until counterbalance lift cable is taut. Now attach locking pliers to the torsion shaft and brace locking pliers against the jamb to keep counter- balance lift cable taut. Repeat the same process for right hand side.

Now, secure the coupler assembly by tightening the (3) 3/8”-16 x 1-3/4” hex head screws and the (3) 3/8”-16 hex nuts.

Set	Counterbalance	Set
collar	lift cable	collar
	Torsion	Set
	keyed shaft	screw

22	Securing Door For Spring Winding(s)
	Tools: Vice Clamps

With the door in the fully closed position, place vice clamps onto both vertical tracks just above the third track roller. This is to prevent the garage door from rising while winding springs.

WARNING

Failure to place vice clamps onto vertical track can allow door to raise and cause severe or fatal injury.

IMPORTANT: Inspect each counterbalance lift cables making sure they are seated properly onto the cable drums and that both counterbalance lift cables have equal tension.

	Left hand	Jamb
	end bearing
	bracket
Counterbalance lift		Cable drum
cable installed	Torsion
		set screws
	shaft
	Locking	Counterbalance lift cable
	pliers
	Left hand
	cable
	drum

Vice clamps above third track roller on both sides of door

Vice clamps attached to inner and outer rail of vertical track

Bottom section

14

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,

refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com