Wayne-Dalton 8800 Top Bracket, Lift Handle, Lift handle outside, Lift handle inside

8	Top Bracket
Tools Needed:	NOTE: Top brackets are attached 1-3/4” down from the
	top edge of the top section..
Power Drill	For single top brackets:
7/16” Socket	Place a top bracket onto the top left hand corner of the
	top section and down 1-3/4”. Align the edge of the
Driver
	top bracket with the edge of the section, and secure
	using (2) 1/4” x 7/8” self drilling screws in the top
	door section rail and (2) 1/4” x 7/8” self drilling screws

1-3/4” Down

from edge of

top section

top bracket

base

end stile

top section

(4)1/4” x 7/8” self drilling screws

into the stile as shown. Place the top bracket slide on

top of the top bracket base. Loosely secure the top

bracket slide to the top bracket base using (1) 1/4 x

5/8” carriage bolt.

Repeat for the other side.

For double top brackets:

Position another top bracket next to the previously

installed top bracket as shown. Leave space between

the brackets to allow the top bracket slides to move

freely. Secure the top bracket to the section using (2)

1/4” x 7/8” self drilling screws in the top door section

rail and (2) 1/4” x 7/8” self drilling screws into the

stile as shown. Place the top bracket slide on top of

the top bracket base. Loosely secure the top bracket

slide to the top bracket base using (1) 3/8” - 16 x 3/4”

hex head bolt and a 3/8” x 16 hex nut.

Repeat for the other side.

(1) 3/8” - 16

hex nut

	top	top section
	bracket
	slide
(1) 3/8” - 16 x 3/4”	top
	bracket
Hex head bolt
	base

top

bracket

assembly

top section

9	Lift Handle		Lock
			Section
Tools Needed:	Bottom section		Lift
	Locate the center most stile of the bottom section of the door.		handle
Tape Measure	On the inside of the door, center the lift handle vertically with				Lock
	the center stile; horizontally on the bottom section rail, and
					Section
	within 8” of the bottom of the section. Using the lift handle as
Pencil
	a template, place a mark at each hole location onto the bottom
Power Drill	section rail. Drill a 9/32” diameter through the section at each		(2) 1/4” x 7/8”	Lift
	marked location. Be extremely careful to keep drill straight.		self drilling
				handle
			screws
	Assemble the outside and inside lift handle to the section using
9/32” Drill Bit		bottom			bottom
	(4) 1/4” x 7/8” self drilling screws.
		Section			Section
1/2” Drill Bit	Lock (2nd) section		lift handle outside
1/4” Wrench	Locate the center most stile on the lock (2nd) section of the				Lock
	door. Position the lift handle’s bottom hole 4” from the bottom		Lock
	of the lock (2nd) section. Center the lift handle vertically on				Section
			Section
Vice Clamps	the center stile and vertically align with the lift handle on the
	bottom section. Using the lift handle as a template, place
	mark at each hole location onto the center stile. Drill a 9/32”
	diameter through the section at each marked location. Be
	extremely careful to keep drill straight.
		Lift		Lift
	Assemble the outside and inside lift handle to the section using			handle
		handle
	(4) 1/4” x 7/8”.
	WARNING		(2) 1/4”
	TO AVOID POSSIBLE INJURY, LIFT HANDLES THAT ARE		Hex Nuts		bottom
	INSTALLED WITHIN 4 INCHES OF A SECTION INTERFACE		bottom Section		Section
	SHALL PROMOTE VERTICAL ORIENTATION OF THE HAND.		lift handle inside

12

Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your

local yellow pages/business listings or go to the Find a Dealer section online at www.wayne-dalton.com