Operating Instruction and Parts Manual | Pedestal Series |
|
|
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
Pedestal Sump
Pump
Description
The pedestal pump is designed for home sump applications. The unit is equipped with an
Unpacking
Inspect this unit before it is used. Occasionally, products are damaged during shipment. If the pump or components are damaged, return the unit to the place of purchase for replacement. Failure to do so could result in serious injury or death. Some warning labels come affixed to the pump. Over time, these labels may fade. If this happens, contact Wayne Water Systems for a free replacement label.
Safety Guidelines
This manual contains information that is very important to know and understand. This information is provided for SAFETY and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols.
Danger indicates an imminently
hazardous situation which, if not avoided, will result in death or serious injury.
Warning indicates a potentially
hazardous situation which, if not avoided, could result in death or serious injury.
Caution indicates a potentially hazardous
situation which, if not avoided, may result in minor or moderate injury.
Notice indicates important
information, that if not followed, may cause damage to equipment.
General Safety
Information
California proposition 65
This product or its power cord may
contain chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
General Safety Information
Read these rules and
instructions carefully. Failure
to follow these instructions MANUAL could cause serious bodily
injury and/or property damage.
Do not submerge motor or allow
motor to be exposed to water. Personal injury and/or death could result.
Do not use to
pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Do not
use in a flammable and/or explosive atmosphere. Pump should only be used to pump clear water. Personal injury and/or death could result.
This pump is not designed to handle
salt water, brine, laundry discharge or any other application which may contain caustic chemicals and/or foreign materials. Pump damage could occur if used in these applications and will void warranty.
All wiring must be performed by a
qualified electrician.
If the basement
has water or moisture on the floor, do not walk on wet area until all power is turned off. If
the
A battery backup system should be used. Please contact your local retailer
to order an emergency backup system.
Assembly
Always disconnect
the power source before attempting to install, service, relocate or maintain the pump.
Never touch sump pump, pump motor, water or discharge piping when pump is connected to electrical power. Never handle a pump or pump motor with wet hands or when standing on wet or damp surface or in water. Fatal electrical shock could occur.
Switch | GFCI Grounded |
| Outlet |
Grommet |
|
| 14 in. |
| Dia. |
Float Rod | Min. |
| |
Guide |
|
| 24 in. |
| Min. |
Float |
|
Figure 1 |
|
FLOAT INSTALLATION SPV800, SPV500 | |
& SSPTU50 |
|
1.To attach float for SPV800, SPV500 & SSPTU50. insert float rod through hole in switch lever.
2.Place rubber grommet on float rod in temporary position.
3.Slide float guide onto float rod.
4.Using pliers to hold the float rod, screw the float on.
5.Attach the float guide to pump halfway up the pumps stand and properly align with motor switch.
FLOAT INSTALLATION PTU30, PTU33A & PTU50
1.To attach float for PTU30, PTU33A, and PTU50 begin by sliding the float guide onto the open end of the float rod.
2.Next slide a grommet onto the open end of the float rod about ¼ of the way down.
3.Guide the open end of the float rod through the hole in the switch lever.
4.Place the second grommet onto the open end of the float rod, being sure to keep the float rod inserted into the switch lever.
5.Attach the float guide to pump halfway up the pumps stand and properly align with motor switch.
NOTE: For all replacement float kits installation will be the same as for SPV800, SPV500 & SSPTU50.
REMINDER: Keep your dated proof of purchase for warranty purposes! Attach it to this manual or file it for safekeeping.
© 2009 Wayne Water Systems | For parts, product & service information | |
| visit www.waynepumps.com |
|
