GENERAL INSTRUCTIONS

13

 

 

Slide out Bottom tray - Remove excess grease, then wash with warm soapy water, then rinse.

Flavorizer® bars and Cooking grates - Clean with a suitable brass bristle brush. As needed, remove from grill and wash with warm soapy water, then rinse with water.

Catch pan - Disposable foil trays are available, or you can line the catch pan with aluminum foil. To clean the catch pan, wash with warm soapy water, then rinse.

Thermometer - Wipe with warm soapy water; clean with plastic scrub ball.

Inside cooking module - Brush any debris off of burner tubes. DO NOT ENLARGE BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water and a water rinse.

Inside Lid - While lid is warm, wipe inside with paper towel to prevent grease build-up. Flaking built-up grease resembles paint flakes.

Stainless steel surfaces - Wash with a soft cloth and a soap and water solution. Be careful to scrub with the grain direction of the stainless steel.

Do not use cleaners that contain acid, mineral spirits or xylene. Rinse well after cleaning.

Preserve Your Stainless Steel - Your grill or its cabinet, lid, control panel and shelves may be made from stainless steel. To keep the stainless steel looking its best is a simple matter. Clean it with soap and water, rinse with clear water and wipe dry. For stubborn particles, the use of a non-metallic brush can be used.

IMPORTANT: Do not use a wire brush or abrasive cleaners on the stainless steel surfaces of your grill as this will cause scratches.

IMPORTANT: When cleaning surfaces be sure to rub/wipe in the direction of the grain to preserve the look of your stainless steel.

GAS INSTRUCTIONS

INSTALL GAS SUPPLY

GENERAL SPECIFICATIONS FOR PIPING

Note: Contact your local municipality for building codes regulating outdoor gas barbecue installations. In absence of Local Codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/ CGA-B149.1, Natural Gas and Propane Installation Code. WE RECOMMEND THAT THIS

INSTALLATION BE DONE BY A PROFESSIONAL.

Some of the following are general requirements taken from the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas and Propane Installation Code for complete specifications.

This barbecue is designed to operate at 4.5 inches of water column pressure (.163 psi).

A manual shut-off valve must be installed outdoors, immediately ahead of the quick disconnect.

An additional manual shut-off valve indoors should be installed in the branch fuel line in an accessible location near the supply line.

The quick disconnect connects to a ½ inch NPT thread from the gas source. The quick disconnect fitting is a hand-operated device that automatically shuts off the flow of gas from the source when the barbecue is disconnected.

The quick disconnect fitting can be installed horizontally, or pointing downward. Installing the fitting with the open end pointing upward can result in collecting water and debris.

The dust covers (supplied plastic plugs) help keep the open ends of the quick disconnect fitting clean while disconnected.

Pipe compound should be used which is resistant to the action of natural gas when connections are made.

The outdoor connector must be firmly attached to rigid, permanent construction.

WARNING: Do not route the 10 foot hose under a deck. The hose must be visible.

GAS LINE PIPING

If the length of the line required does not exceed 50 feet, use a 5/8" O.D. tube. One size larger should be used for lengths greater than 50 feet.

Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a minimum wall thickness of .062 inch; or standard weight (schedule 40) steel or wrought iron pipe.

Copper tubing must be tin-lined if the gas contains more than 0.3 grams of hydrogen sulfide per 100 cubic feet of gas.

Plastic tubing is suitable only for outdoor, underground use.

Gas piping in contact with earth, or any other material which may corrode the piping, must be protected against corrosion in an approved manner.

Underground piping must have a minimum of 18" cover.

TEST CONNECTIONS

All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA 54, or CAN/CGA-B149.1

DANGER

Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death and damage to property.

WWW.WEBER.COM®

Page 13
Image 13
Weber E/S 470 GAS Instructions, Install GAS Supply, General Specifications for Piping, GAS Line Piping, Test Connections

E/S 470 specifications

The Weber E/S 470 is a cutting-edge electric bicycle designed to offer an exceptional riding experience while promoting sustainability. It stands out in the electric bike market with its combination of advanced features, robust technology, and comfort-focused characteristics. The E/S 470 caters to a diverse range of cyclists, from daily commuters to recreational riders.

One of the standout features of the Weber E/S 470 is its powerful electric motor. The bike is equipped with a high-performance mid-drive motor that delivers impressive torque and speed. This ensures that riders can tackle even the steepest hills with ease, while also providing a natural feel that closely mimics traditional cycling. The motor is seamlessly integrated with the bike's gears, allowing for smooth shifting and enhanced control over various terrains.

Battery life is a crucial factor for any electric bike, and the Weber E/S 470 excels in this area. It comes with a high-capacity lithium-ion battery that offers an impressive range on a single charge. Depending on the mode selected, riders can expect anywhere from 40 to 80 miles of assistance, making it perfect for both short commutes and longer adventures. The battery is conveniently detachable, allowing for easy charging at home or in the office.

In terms of design, the E/S 470 is characterized by its sleek and modern aesthetics. It features a lightweight aluminum frame, making it easy to handle while ensuring durability. The bike's geometry is carefully crafted to provide an upright riding position, which enhances comfort, especially during long rides. The inclusion of front and rear suspension allows for a smooth ride over uneven surfaces, absorbing shocks and providing stability.

Technological innovations further enhance the user experience of the Weber E/S 470. The bike is equipped with an intuitive digital display that provides key information such as speed, distance traveled, battery level, and assistance mode. Riders can easily switch between different levels of pedal assist, tailoring the bike's performance to their personal preferences and riding conditions.

Safety is paramount, and the Weber E/S 470 includes high-quality hydraulic disc brakes that ensure reliable stopping power in all weather conditions. The bike also features integrated lighting systems for enhanced visibility during night rides and a set of durable tires designed for traction and stability.

Overall, the Weber E/S 470 is an exemplary model in the world of electric cycling. With its powerful motor, long-range battery, comfortable design, and user-friendly technology, it appeals to a broad audience looking for an eco-friendly and efficient mode of transportation. The E/S 470 embodies the perfect blend of performance and practicality, making it an ideal choice for anyone looking to embrace electric mobility.