REPLACING THE LINE

1.Remove spool by firmly pulling on tap button.

2.Clean entire surface of hub and spool.

3.Replace with a pre-wound spool, or cut two lengths of 12-1/2feet of 0.080! (2 mm) di- ameter Weed Eaterr brand line.

WARNING: Never use wire, rope, string, etc., which can break off and become a dangerous missile.

4.Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.

Spool

Small

Holes

Line exit holes

Line in Notch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Line in Notch

Hub

5.Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.

6.Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.

7.Insert the lines into the the exit holes in the hub as shown in the illustration.

8.Align the notches with the line exit holes.

9.Push spool into hub until it snaps into place.

10.Pull the lines extending outside of the hub to release the lines from the notches.

REPLACING THE CUTTING HEAD

1.Align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup.

2.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while removing and installing trimmer head.

Screwdriver

3.While holding the screwdriver in position, remove trimmer head by turning clock- wise.

4.Thread replacement trimmer head onto the shaft by turning counterclockwise. Tighten until secure.

5.Remove the screwdriver.

CARBURETOR ADJUSTMENT

Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an au- thorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.

WARNING: Perform the following steps after each use:

SAllow engine to cool before storing or trans-

porting.

SStore unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci- dentally cause injury.

SStore unit and fuel well out of the reach of children.

SEASONAL STORAGE

Prepare unit for storage at end of season or if it will not be used for 30 days or more.

If your unit is to be stored for a period of time: S Clean the entire unit before lengthy

storage.

SStore in a clean dry area.

S Lightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA- TION section of this manual, see message la- beled IMPORTANT regarding the use of ga- sohol in your engine.

Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol- low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom- mended type and heat range.

SClean air filter.

S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts.

8

Page 7 Page 9
Page 8
Image 8
Weed Eater 530163507 Replacing the Line, Replacing the Cutting Head, Carburetor Adjustment, Seasonal Storage, Fuel System
Page 7 Page 9

530163507 specifications

The Weed Eater 530163507 is a remarkable string trimmer designed for both homeowners and landscape professionals looking to maintain a pristine garden or yard. Boasting a combination of lightweight design and powerful performance, this trimmer stands out in the competitive landscaping market.

One of the main features of the Weed Eater 530163507 is its robust 25cc two-cycle engine. This engine provides the necessary power for trimming through tough grass and weeds, making it an ideal choice for tackling overgrown areas. The engine is designed to deliver efficient fuel consumption, allowing users to work longer hours without the need for constant refueling, thus enhancing productivity.

The trimmer features a unique bump feed line advancement system, which allows for easy and quick line replacement during operation. By simply tapping the trimmer head on the ground, users can release more line without needing to stop their workflow. This feature is especially invaluable when working in large areas or for extended periods, as it minimizes interruptions.

Comfort and ease of use are also prioritized in the design of the Weed Eater 530163507. It comes equipped with an adjustable handle that allows users to customize the trimmer's height and angle according to their preference. This enhances control and maneuverability, making it easier to reach those tricky spots around flower beds and trees. The cushioned grip further adds to operator comfort, reducing fatigue during prolonged use.

Safety features are integrated into the design of the trimmer, including a protective guard that shields the user from flying debris. Additionally, the lightweight construction makes it easy to carry and operate, reducing the strain on the arms and back.

In terms of technology, the Weed Eater 530163507 incorporates advanced engineering to create a reliable and durable tool. The trimmer is built to resist wear and tear, ensuring longevity despite regular use. Its effective vibration-dampening system minimizes operator discomfort, allowing for a smoother, more enjoyable trimming experience.

In summary, the Weed Eater 530163507 is a well-rounded string trimmer that combines power, efficiency, and user comfort. Whether you are a weekend warrior tending to your garden or a professional landscaper maintaining various properties, this trimmer offers the features and performance needed to achieve excellent results. Experience the ease and efficiency of maintaining your outdoor spaces with this quality tool.
Top Page Image Contents