
15. Pull the excess Upper Wire Harness (71) out of | 15 |
|
|
|
the Upright (2). Insert the connector on the |
|
|
| |
|
| 114 | ||
Console (67) into the socket on the Upper Wire |
|
| ||
|
|
|
| |
Harness. The connector should slide easily into |
|
|
|
|
the socket and snap into place. If the connector |
|
|
|
|
does not slide easily and snap into place, turn the | 71 |
|
|
|
connector over and then insert it. |
| 2 |
| |
67 |
|
| ||
|
|
|
| |
Make sure that the connector and wires appear |
|
| 114 | |
as shown in the inset drawing. IF THE CONNEC- |
|
|
|
|
TOR IS NOT INSERTED PROPERLY, THE CON- |
|
|
|
|
SOLE MAY BE DAMAGED WHEN THE POWER |
|
|
|
|
IS TURNED ON. |
|
|
|
|
Push the excess Upper Wire Harness (71) into |
|
|
| 67 71 |
|
|
|
| |
the Upright (2). | 16 |
|
|
|
|
|
|
| |
Attach the Console (67) to the Upright (2) with |
|
| 68 |
|
four M4 x 70mm Screws (114). |
|
| 43 | |
|
|
| ||
16. Attach a Large Pulley (14) and the Pulley Plate |
|
|
|
|
(68) to the Upright (2) with an M12 x 62mm |
|
|
|
|
Button Bolt (81) and an M12 Nylon Locknut (43). |
|
| 14 |
|
Do not tighten the Locknut yet. |
|
|
| |
|
|
|
| |
17. Pull the upper cable (A), which is attached inside | 81 |
| 2 |
|
of the Mech Frame (not shown), up between the |
|
|
| |
|
|
|
| |
Upright (2) and the Pulley Plate (68). |
|
|
|
|
Attach another Large Pulley (14) to the Upright (2) |
|
|
|
|
and Pulley Plate (68) with an M12 x 62mm Button | 17 |
|
|
|
Bolt (81) and an M12 Nylon Locknut (43). Make |
|
|
| |
|
|
|
| |
sure that the upper cable (A) is between the |
|
|
| A |
two Pulleys. |
|
| 90 | 42 |
|
|
| ||
|
|
|
| |
Hold the 38mm Spacer (90) inside the loop of the |
|
| 43 |
|
upper cable (A), and between the Upright (2) and |
|
|
| |
the Pulley Plate (68). Attach the Spacer with an |
|
| 68 | |
M10 x 58mm Button Screw (42). Make sure the | 81 |
|
| 14 |
ends of the cable do not wrap around each |
| 2 | ||
|
|
| ||
other below the Spacer and the Large Pulleys |
|
|
| |
|
|
|
| |
(14) used in steps 16 and 17 (refer to the |
|
|
|
|
CABLE DIAGRAM on page 20). |
|
|
|
|
Tighten the M12 Nylon Locknuts (43) used in | 18 |
|
|
|
|
|
|
| |
steps 16 and 17. |
| 17 |
|
|
| 18 |
|
| |
18. Attach a Small Guide Spacer (18), a Large Guide |
|
| 86 | |
|
|
|
| |
Spacer (17), and two Bar Guides (15) to the |
| 15 |
|
|
Upright (2) with an M10 x 152mm Bolt (86). |
| Metal |
| |
|
| 54 | ||
Pull the upper cable (A) up between the Bar | 2 | A | Cover | |
|
|
| ||
|
|
|
| |
Guides (15). Press the metal cover on the cable |
|
|
| 86 |
into the groove in the Block Spacer (16). Attach a |
|
|
| |
|
|
|
| |
Small Guide Spacer (18), the Block Spacer, the |
|
|
| 70 |
two Bar Guides (15), an M10 Thick Washer (54), |
|
|
| |
|
|
|
| |
and the two Tethers (70) to the Upright (2) with | 18 | 16 | Groove |
|
another M10 x 152mm Bolt (86). Do not tighten |
|
|
| |
|
|
|
| |
the Bolt yet. |
|
|
|
|
| 10 |
|
|
|