8. | Pull the Seat Knob (48) out and slide the Seat | 8 |
|
|
|
|
| Carriage (44) onto the Rail (4) as shown. Engage |
|
|
|
| |
|
|
|
|
|
| |
| the Knob into a hole in the Rail. |
| 103 |
|
|
|
|
|
|
|
|
| |
| Press the Rail Cap (49) onto the Leg (5). Attach |
| 106 | 4 |
|
|
|
|
|
|
|
| |
| the Leg to the Rail (4) with two M10 x 64mm |
|
|
|
|
|
| Button Bolts (80), four M10 Washers (106), and |
|
|
| 44 | 48 |
| two M10 Nylon Locknuts (103). |
|
|
| ||
|
|
|
|
| Holes on | |
|
|
| 49 | 106 | this side | |
|
|
|
| 80 |
| |
|
|
|
|
|
| |
|
|
| 5 |
|
|
|
9. | Attach the Rail Insert (31) inside of the Rail (4) | 9 |
| 31 |
|
|
| with two M10 x 64mm Button Bolts (80), four M10 |
|
|
| ||
| 103 | 106 |
|
| ||
| Washers (106), and two M10 Nylon Locknuts |
|
|
| ||
|
|
|
|
|
| |
| (103). Make sure the Bolts go through the indi- |
|
|
|
|
|
| cated holes in the Rail Insert. | 4 |
|
| Holes |
|
|
|
| 106 |
| ||
|
|
| 106 |
| 80 |
|
|
|
|
|
|
| |
10. | Lubricate an M10 x 125mm Button Bolt (89) with | 10 |
| 29 |
|
|
| grease. Attach the Rail (4) to the Row Plate (28) |
|
|
| ||
|
|
|
|
| ||
|
|
|
|
|
| |
| with the Bolt, two M10 Washers (106), two 31mm |
|
|
|
|
|
| Spacers (30), and an M10 Nylon Locknut (103). |
|
|
|
|
|
| Do not overtighten the Locknut; the Rail must | 103 | 106 |
| 28 |
|
| be able to pivot easily. |
|
| |||
|
|
|
| |||
| Tighten the Storage Knob (29) into the Row Plate | 30 |
|
|
| |
| (28) and the Rail (4). |
|
|
| ||
|
|
|
|
|
| |
|
|
| 4 | 30 |
|
|
|
|
|
| 106 |
| 89 |
|
|
|
|
| Lubricate | |
11. | Wet a Squat Arm (20) with soapy water. Slide a | 11 |
|
|
|
|
| Small Foam Pad (24) and a Short Handgrip (21) | 20 |
|
|
| |
|
| 27 |
|
| ||
| onto the Squat Arm. |
|
|
|
| |
|
|
|
|
|
| |
| Repeat with the other Squat Arm (20). |
|
|
|
|
|
| Tighten the Squat Knob (27) into the Squat |
|
| 20 |
|
|
| Carriage (19) and the Squat Arm Pivot Tube (not |
|
|
|
| |
| shown). |
| 19 |
|
|
|
|
|
|
| 24 |
| |
|
|
|
|
|
| |
|
|
|
|
|
| 21 |
|
| 8 |
|
|
|
|
