CABLE ASSEMBLY

18. Route the Long Cable (23) around the ÒVÓ-

18

 

 

50

7

Pulley (6) on the Right Arm (48). Be sure

 

 

 

 

 

that the Cable is in the groove of the ÒVÓ-

 

 

 

 

6

 

 

 

 

 

Pulley and that the Long Cable Trap (50) is

 

 

 

 

 

turned to hold the Cable in place. Tighten

 

 

 

 

 

the 3/8Ó x 2 1/2Ó Bolt (7) and the 3/8Ó Nylon

 

 

 

 

 

Locknut (not shown).

 

 

 

 

 

 

 

 

 

 

48

 

 

 

23

 

 

19. Route the Long Cable (23) around the 3 1/2Ó

19

 

68

66

 

Pulley (15) attached to the Pulley Bracket

 

 

 

 

 

 

(20). Be sure that the Cable is in the

 

 

 

 

 

groove of the Pulley and that the Cable

 

 

 

 

 

Trap (66) is turned to hold the Cable in

 

20

 

 

 

place. Tighten the 3/8Ó x 2Ó Bolt (12) and the

 

 

 

 

 

3/8Ó Nylon Locknut (not shown).

 

12

 

 

 

 

 

 

 

 

Be sure that the 5/16Ó x 5Ó Bolt (68) is proper-

 

23

 

15

 

ly tightened and that the Pulley Bracket (20)

 

 

 

 

 

 

 

 

 

can move freely.

 

 

 

 

 

20. See the inset drawing. Attach a 3 1/2Ó Pulley

20

 

 

 

 

(15) and a Cable Trap (66) to the indicated

 

 

 

 

 

 

 

 

 

hole in the Long ÒUÓ-Bracket (57) with a 3/8Ó x

 

 

 

 

 

2Ó Bolt (12) and a 3/8Ó Nylon Locknut (21). Be

 

 

 

 

 

sure that the Cable Trap is inside the ÒUÓ-

 

 

 

 

 

Bracket. Note: This may come pre-assem-

 

 

 

 

 

bled.

 

23

 

 

23

 

 

 

 

 

 

 

 

 

Route the Long Cable (23) around the 3 1/2Ó

 

66

15

 

 

Pulley (15) and through the Long ÒUÓ-Bracket

 

12

 

 

(57). Be sure that the Cable is in the

 

 

 

 

 

21

 

 

 

groove of the Pulley and that the Cable

 

 

 

 

 

57

 

 

 

and Pulley move smoothly.

 

 

 

 

 

 

 

 

 

21. Note: The 3 1/2Ó Pulley (15) labeled in this

21

 

 

 

15

step is pre-attached. It is shown removed

 

 

23

 

 

 

for easy part identification.

 

 

Bracket

12

 

 

 

 

 

Route the Long Cable (23) around the 3 1/2Ó

 

 

 

 

 

Pulley (15) attached to the bracket on the Top

 

 

55

 

 

Frame (55). Tighten the 3/8Ó x 2Ó Bolt (12)

 

 

 

 

 

 

 

 

 

and the 3/8Ó Nylon Locknut (21). Be sure that

 

 

 

 

 

the Cable is in the groove of the Pulley

 

 

 

 

 

and that the Cable and Pulley move

 

 

21

 

 

smoothly.

 

 

 

 

 

11

Page 11
Image 11
Weider WESY85290 manual Cable Assembly