6. Press a Weight Tube Bumper (64) into the end of | 6 |
|
|
|
the other Weight Tube (63). Insert the Weight |
|
|
| |
|
|
|
| |
Tube into the rear stack of Weights (25). Be sure |
|
| Holes |
|
that the pins on the Weight Tube are sitting in |
|
|
| |
the pin grooves in the top Weight (refer to |
|
|
|
|
step 4). |
|
| 73 |
|
|
|
|
| |
Lubricate the inside of the holes in the other Top |
|
|
|
|
Weight (65). Set the Top Weight onto the rear |
|
|
|
|
stack of Weights (25). Insert both Short Weight | Lubricate |
|
|
|
Guides (73) into the stack of Weights. Be sure |
|
|
| |
|
|
|
| |
that the holes in the Weight Guides are at the |
|
|
|
|
top, as shown. |
|
|
|
|
| 65 |
|
|
|
| Pin |
|
|
|
| 63 |
|
|
|
| 64 |
| 25 |
|
|
|
|
| |
7. Attach the upper ends of the Long Weight Guides | 7 |
|
|
|
(62) to the Top Frame (55) with a 5/16” x 6” Bolt |
|
|
| |
|
|
|
| |
(60), two 1/2” x 3/4” Spacers (61), and a 5/16” | 61 | 3 | 61 |
|
Nylon Locknut (3). Be sure that the Pulley | 3 | |||
Bracket (20) is in front of the right Long |
|
|
| |
Weight Guide, as shown. | 60 |
|
| 55 |
|
|
| ||
|
|
|
| |
Attach the upper ends of the Short Weight Guides |
|
|
|
|
(73) to the Top Frame (55) with a 5/16” x 6” Bolt |
|
|
|
|
(60), two 1/2” x 3/4” Spacers (61), and a 5/16” |
| 60 |
|
|
Nylon Locknut (3). |
| 73 |
| 20 |
|
|
| ||
|
| 62 |
|
|
ARM ASSEMBLY | 8 |
|
|
|
|
|
|
| |
8. Press a 1” x 7/8” Plastic Bushing (90) onto each |
|
|
| 59 |
welded spacer on the Press Frame (17). Slide the |
|
|
| |
Press Frame into place onto the Base (4). Note: |
|
|
| 17 |
|
|
|
| |
This will be a tight fit. The Plastic Bushings |
|
|
|
|
should fit on each end of the indicated tube in |
|
|
| Lubricate |
the Base. Make sure that the pulleys are on |
|
|
| |
the side shown. | 4 |
|
| Welded |
| Tube |
|
| |
Lubricate the 3/8” x 8” Bolt (59). Attach the Press |
|
| Spacers | |
|
|
| ||
|
| 21 |
| |
Frame (17) to the Base (4) with the Bolt and a |
|
| 90 | |
|
|
| ||
3/8” Nylon Locknut (21). |
|
|
|
|
| 8 |
|
|
|
