Whirlpool 3390148 installation instructions If duct Extends Too far to make the exhaust duct

Internal \ exhaust duct

dryel rear

Y

6.[Insert elbow end of duct pieces through the side opening. Reach through the access panel openlng and attach elbow to the Internal exhaust duct. Check the length of stralght duct extending out the

side of	the	cabinet.	If duct		extends
too far to make the exhaust duct
connection,		mark	a line	around		the
stralght duct one Inch out from the
cabinet.		Remove	the duct		and	elbow
and cut the straight pipe to the
length	needed.		Reinsert	the duct
pieces.	Use duct		tape	to	connect

the elbow to the internal exhaust due Repeat for the other dryer.

3.1Remove duct tape from In .ernal exhaust duct and the straight duct.

4.j Remove the screw from the I duct clip tit attaches the straight duct to the back of the cabinet. Dep Bss the clip and remove the straight c uct using a twisting motion througl i the rear exhaust openlng.

5.1Measure from the large en( 1 of the straight duct and mark at four inches. Cut the stralght duct to that

4Aont

of dryer

:: I :I--

10. :Push the four inch, stralght duct through the rear exhaust opening and onto the Internal duct.as far as it will go.

ol!*front d dryer

I

7 1. j Insert me elbow through the rear exhaust opening. Ins& elbow into the bottom exhaust openina.

>7.llnsert the plasttc cover Into the rea exha-ust opening.

8.jRe place the access panels.

9.\Use duct tape to seal all joints.

To connect exhaust duct through the bottom of the lower dryer only -

Note: You must use a threesection elbow to connect exhaust duct through the bottom of the tower dryer.

I..\ Check that the legs extend one inch from the bottom of the dryer.

2.i Remove the lower dryer access panel by releasing the two locking clips with a small, flat-blade

screwdrtter. The clips are located four inches in from each side of-the access panel. Uft access panel off the bottom clips and set aside.

Page 8

+

tront

of

dryer

6.j Reach through the rear ezdxlust

opening

and

depress center ctf tabs

on one of the side, plcxtic opt ning

covers..

Remove

the cover.

12.‘Slide

the

straight

du

elbow

approximatety

one

inch.

Use duct tape to seal both joints.

.

sc,ew h&d

x-

(fastens

against

edge

of cabinet)

iili~rt

the

7.1 With

a

Phillips

screwdriver,

reach

bottom

exhaust

-cover

through

through the rear exhaust oper ling

the

side

exhaust

and remove the screw that al taches

opening.

Put

me

me cover to the dryer base.

cover

over

me

Carefully remove the cover ar d screw

rear

exhaust

through

the rear

exhaust

oper

ring.

opening

with

the

tab

pointing

down

to bottom

of

dryer.

Insert screw through the hoie In the

floor

Damage

cover

that

Is on the

&tslde

of

the

cabinet.

Ttghten

screw.

Slide dryers onto cardbaal d or

hardboard

before

moving

14jReptace

the

side

exhaust

across

tloor.

cover.

Failure to do so mq.causc!

damage

to floor

covering.

15. (Move the dryers into operating

I

1

position.

Check

that

the

elbow

Is

8.\, Move

dryers

into

operatinc

through

the

bottom

exhaust

opening.

Replace

the

access

pdsltion.

Reach

through

the

2 access

panel.

opening

and

mark the exhau: t

opening

location

on

the

floor. Move

763onnect

the

elbqy

toe-must

dryers

out

of

the

operating

pc sition.

d&t.

Then

connect

exhaust duct

to exhaust hood or maln exhaust.

9.: Cut

opening

through

the

fl oar.

Use duct tape to seal all Joints.