Solid elements hold heat longer than conventional surface units. For best cooking results, use a high setting for only a short period of time. Then use a lower setting to complete the cooking. You may want to turn the solid element surface unit OFF a few minutes before you finish cooking.
Bum, Fire And
Property Damage Hazard
. Be sure all control knobs are turned to OFF and all signal lights are off when you are not cooking. Someone could be burned or a fire could start if a surface unit is accidentally left on.
. Solid elements stay hot for a long time. Do not use the high setting for long periods of time or leave pans on hot elements when cooking is done. Burned food and damage to the cookware could result.
Cookware
Pans should be the same size or larger than the surface umt to prevent boil- overs and hot handles.
Use only flat-bottomed utensils. Flat bottoms allow maximum contact between the pans and surface units for fast, even cooking. Pans with uneven bottoms or with raised patterns on the bottoms are not suitable. Do not use trivets, woks with skirts, or canners with concave or ridged bottoms.
To check your cookware for flatness, place a straight-edge across the bottom of each piece. Rotate the straight-edge across the bottom. If light shows anywhere between the pan and the straight-edge, the pan is not flat. Do not use it.
Page 6
Bum And Product Damage Hazard
.If the pan is too small for the surface unit, you could be burned by the heat from the exposed section of the surface unit. Use correctly sized cooking utensils to prevent injury.
. If a surface unit stays red for a long time, the bottom of the pan is not flat enough or is too small for the surface unit. Prolonged usage of incorrect utensils for long periods of time can result in damage to the surface unit, cooktop, wiring and surrounding areas. To prevent damage, use correct utensils, start cooking on high setting and turn control down to continue cooking.
L
Setting the clock and timer (Models FEC350V, FEP350V, FEP340V, FEP335V & FEP330V)
Electronic clock and timer (Models FEP340V,FEP335V&
FEP330V)
The clock/timer acts as both a time-of-day clock and as a minute timer.
To set time of day:
When the range is connected to power, the clock display will blink at 88 :88 until the time-of-day is set. To set time-of-day, depress the Set Button once. The triangle and clock signal lights on the display will light up and remain lit until the time is set. Within 15 seconds, turn the Clock/ Timer Knob to the correct time.
To set the timer:
Turn the Clock/Timer Knob clockwise to the desired setting, up to 9 hours 50 minutes. (Knob must be turned four or five clicks before time will advance.) The triangle and bell signal lights will light up. The timer will count down the time while flashing the time-of-day every 12 seconds. Three beeps will sound at the end of the set time and the signal lights will go off.
Electronic clock with cook and minute timer (Models FEC350V & FEP35l-W
-------I
This electronic control acts as a time-of- day clock, as a minute timer up to 9 hours 50 minutes, and as an automatic stop timer which allows you to begin cooking now and set the oven to turn itself off later.
To set time of day:
When the range is connected to power, the clock display will blink at 88:88 until the time-of-day is set. Turn the Clock/ Timer Knob in either direction to set time-of-day. (Knob must be turned four or five clicks before time will advance.)
To set the minute timer:
Push the Set Button once. A beep will sound and a bell will light on the display. Turn the Clock/Timer Knob clockwise to the desired setting, up to 9 hours 50 minutes.
NOTE: The knob must be turned within 15 seconds after the button is pushed.
The timer will count down the time and sound a tone at the end of the set time.
To check time-of-day during a minute timer interval:
. Push the Set Button once. A beep will sound and the time-of-day will be displayed.
To return to the minute timer display:
nPush the Set Button once. A beep will sound and the minute timer will reappear.
To set the automatic stop timer:
1.Set the Time Bake Switch to TIME BAKE. The TIME BAKE Signal Light will light.
2.Turn the Oven Temp Control to the desired oven temperature.
3.Push the Set Button twice. A beep will sound with each push and a bell will light on the face of the clock along with the word “AUTO”
4.Turn the Clock/Timer Knob to the desired cook time up to 9 hours 50 minutes.
NOTE: Knob must be turned within 15 seconds after button is pushed.
The oven will turn on within the next 30-40 seconds and will turn off automatically at the end of the set cook time.
To check time-of-day during cooking:
. Push the Set Button once. A beep will sound and the time-of-day will be displayed.
To return to the cook time display:
. Push the Set Button once. A beep will sound and the automatic cook time will reappear.
At the end of the set cook time, a tone will sound. Turn Oven Temp Control to
OFF and set the Time -.-. .Bake Switch to
MANUAL BAKE.
IMPORTANT: After the oven has turned off, the Time Bake Switch must be returned to “Manual Bake”. IF THE TIME BAKE SWITCH IS NOT SET TO “MANUAL BAKE ,,, THE OVEN W-ILL NOT WORK PROPERLY.
