Whirlpool GZ5736, GZ5730 Now start, Prepare hood, 3-1/4x 10 8.3 x 25.4 cm vent system

Models: GZ5730 GZ5736

1 20
Download 20 pages 43.7 Kb
Page 4
Image 4
3-1/4" x 10" (8.3 x 25.4 cm) vent system

3-1/4" x 10" (8.3 x 25.4 cm) vent system

3-1/4" x 10"

(8.3 x 25.4 cm) elbow

6 ft. ( 1.8 m)

 

 

 

 

wall cap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum length

=

65 ft.

(19.8 m)

 

 

 

 

1 - 90° elbow

=

5 ft.

(1.5 m)

 

 

 

8 ft. (2.4 m) straight

=

8 ft.

(2.4 m)

2

ft.

 

(0.6 m)

1 - wall cap

=

0 ft.

(0 m)

 

 

 

 

Length of 3-1/4" x

 

 

 

 

 

 

 

 

10" (8.3 x 25.4 cm)

 

 

 

 

 

 

 

 

system

=

13 ft.

(4 m)

Recommended standard fittings

3-1/4" x 10"

3-1/4" x 10"

3-1/4" x 10"

(8.3 x 25.4 cm)

(8.3 x 25.4 cm)

(8.3 x 25.4 cm)

90° elbow =

flat elbow =

wall cap =

5 ft. (1.5 m)

12 ft. (3.7 m)

0 ft. (0 m)

7" (17.8 cm) vent system

90° elbow

 

 

 

 

 

6 ft. (1.8 m)

 

 

wall cap

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

ft. (0.6 m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Maximum length

=

65 ft. (19.8 m)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

- 90° elbows

=

5 ft.

(1.5 m)

 

1

- wall cap

=

0 ft.

(0 m)

 

 

 

 

 

 

 

8 ft. (2.4 m) straight =

8 ft.

(2.4 m)

 

 

 

 

 

 

 

Length of 7"

 

 

 

 

 

 

 

 

 

 

(17.8 cm) system

=

13 ft.

(4 m)

Recommended standard fittings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

90° elbow =

45° elbow =

7" (17.8 cm)

3-1/4" x 10"

3-1/4" x 10"

5 ft. (1.5 m)

2.5 ft. (0.8 m)

wall cap =

(8.3 x 25.4 cm) to

(8.3 x 25.4 cm)

 

 

 

 

 

 

0 ft. (0 m)

7" (17.8 cm) =

to 7" (17.8 cm)

 

 

 

 

 

 

 

 

 

4.5 ft. (1.4 m)

90° elbow =

 

 

 

 

 

 

 

 

 

 

5 ft. (1.5 m)

Now start...

With range hood in kitchen.

Slide cardboard or hardboard under range before moving range across floor to prevent damaging floor covering.

Cover countertop, cooktop or set-in range with a thick, protective covering to prevent damaging them.

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine which venting method (roof or wall venting or non-venting) you need to use. This range hood is shipped for vented installation.

Prepare hood

location wood shim strips (recessed cabinet bottoms only)

 

 

 

 

 

10-1/2"

A

 

 

 

A

 

 

 

 

(26.7 cm)

 

 

 

cabinet

centerline

bottom

 

wall

1/8" (3.0 mm)

1-1/2"

 

pilot holes

(3.8 cm)

 

 

 

 

hood size

 

A

 

30" (76.2 cm)

 

13-15/16" (35.4 cm)

36" (91.4 cm)

 

16-15/16" (43.0 cm)

 

 

 

 

3.Drill four 1/8" (3.0 mm) pilot holes for hood mounting screws. If cabinet has recessed bottom, add wood shim strips on each side.

4

Page 4
Image 4
Whirlpool GZ5736, GZ5730 Now start, Prepare hood, 3-1/4x 10 8.3 x 25.4 cm vent system, Recommended standard fittings