LocationRequirements

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered. Proper installation is your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”

Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).

A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended.

A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures.

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

2" (5 cm)

 

 

36" min.

 

 

(91.4 cm)

 

 

1"

27"

1"

(2.5 cm)

(68.6 cm)

(2.5 cm)

Recommended installation spacing for recessed or closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

Installation clearances

The location must be large enough to allow the washer door to be fully opened.

Additional spacing should be considered for ease of installation and servicing. The door opens more than 90°, and it is not reversible.

Additional clearances might be required for wall, door, and floor moldings.

Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer.

Companion appliance spacing should also be considered.

Washer Dimensions

 

 

48"

 

 

(122 cm)

1"

30¹⁄₂"

4"

(2.5 cm)

(77.5 cm)

(10.2 cm)

 

A

 

 

3"

 

(7.6 cm)

48 in.2

 

(310 cm2)

 

24 in.2

3"

(155 cm2)

 

(7.6 cm)

B

A. Side view - closet or confined area

50¹⁄₄"

27"

(68.6 cm)

B. Closet door with vents

(127.6 cm)

Recessed or closet installation - Washer on pedestal

36"

(91.4 cm)

30¹⁄₂"

(77.5 cm)

1"

27"

1"

(2.5 cm)

(68.6 cm)

(2.5 cm)

A

 

 

38" min.

 

 

(96.5 cm)

1"

30¹⁄₂"

4"

(2.5 cm)

(77.5 cm)

(10.2 cm)

 

B

 

A. Recessed area

B. Side view - closet or confined area

5

Page 5
Image 5
Whirlpool W10133484A manual LocationRequirements, Installation clearances, Washer Dimensions

W10133484A specifications

The Whirlpool W10133484A is an innovative appliance designed to elevate the functionality and efficiency of kitchen spaces. This high-quality kitchen accessory is primarily known for its versatility in enhancing meal preparation and ensuring a seamless cooking experience.

One of the standout features of the W10133484A is its robust design, built to endure the demands of a busy kitchen. Its stainless steel construction not only offers durability but also adds a modern touch to any kitchen décor. The aesthetic appeal is complemented by its user-friendly interface, making it easy for users to operate without needing extensive technical knowledge.

Equipped with advanced technology, the W10133484A boasts a variety of performance enhancements. One such feature is its energy efficiency, which helps users save on utility bills while reducing their environmental impact. This appliance is designed to use minimal resources, allowing for sustainable operation without sacrificing performance.

The W10133484A also integrates various cooking modes and settings, catering to the diverse needs of home chefs. Whether you are baking, broiling, or simply warming food, this appliance adapts to different cooking styles, ensuring optimal results. The intuitive control panel allows users to easily select settings for precise cooking, while the timer function provides added convenience, allowing you to multitask without worry.

In terms of capacity, the W10133484A is designed to accommodate a range of food items, making it suitable for both small family meals and larger gatherings. The spacious interior enables users to cook multiple dishes simultaneously, saving time and effort in the kitchen.

Safety features are also paramount in the design of the W10133484A. This appliance includes automatic shut-off mechanisms and cool-touch exteriors, ensuring that it is safe to use even in a bustling kitchen environment.

Overall, the Whirlpool W10133484A stands out as a reliable kitchen companion that combines style, efficiency, and user-friendly technology. Its thoughtful design and features make it an essential addition for anyone who values quality and practicality in kitchen appliances. Whether you are a seasoned chef or a cooking novice, the W10133484A will undoubtedly enhance your culinary experience and simplify your cooking processes.