INSTALLATION INSTRUCTIONS

RemoveTransportSystem

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the unit is within approximately 3 ft (90 cm) of its final location.

There are 4 blue bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

1.Using a 13 mm wrench, loosen each of the bolts.

2.Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.

3.Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.

4.Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your local service center. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.

ConnecttheInletHoses

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

AB

A.Coupling

B.Washer

Connect the inlet hoses to the water faucets

Make sure the washer drum is empty.

1.Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

2.Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3.Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

■Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

■Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

8

Page 7 Page 9
Page 8
Image 8
Whirlpool W10133484A manual Installation Instructions, RemoveTransportSystem, ConnecttheInletHoses, Clear the water lines
Page 7 Page 9

W10133484A specifications

The Whirlpool W10133484A is an innovative appliance designed to elevate the functionality and efficiency of kitchen spaces. This high-quality kitchen accessory is primarily known for its versatility in enhancing meal preparation and ensuring a seamless cooking experience.

One of the standout features of the W10133484A is its robust design, built to endure the demands of a busy kitchen. Its stainless steel construction not only offers durability but also adds a modern touch to any kitchen décor. The aesthetic appeal is complemented by its user-friendly interface, making it easy for users to operate without needing extensive technical knowledge.

Equipped with advanced technology, the W10133484A boasts a variety of performance enhancements. One such feature is its energy efficiency, which helps users save on utility bills while reducing their environmental impact. This appliance is designed to use minimal resources, allowing for sustainable operation without sacrificing performance.

The W10133484A also integrates various cooking modes and settings, catering to the diverse needs of home chefs. Whether you are baking, broiling, or simply warming food, this appliance adapts to different cooking styles, ensuring optimal results. The intuitive control panel allows users to easily select settings for precise cooking, while the timer function provides added convenience, allowing you to multitask without worry.

In terms of capacity, the W10133484A is designed to accommodate a range of food items, making it suitable for both small family meals and larger gatherings. The spacious interior enables users to cook multiple dishes simultaneously, saving time and effort in the kitchen.

Safety features are also paramount in the design of the W10133484A. This appliance includes automatic shut-off mechanisms and cool-touch exteriors, ensuring that it is safe to use even in a bustling kitchen environment.

Overall, the Whirlpool W10133484A stands out as a reliable kitchen companion that combines style, efficiency, and user-friendly technology. Its thoughtful design and features make it an essential addition for anyone who values quality and practicality in kitchen appliances. Whether you are a seasoned chef or a cooking novice, the W10133484A will undoubtedly enhance your culinary experience and simplify your cooking processes.
Top Page Image Contents