Whirlpool W10300929B warranty Dishwasher Feedback Section

OPTION SELECTIONS

OPTIONS	CAN BE	WHAT IT DOES	ADDED TIME TO CYCLE		ADDED
	SELECTED WITH				WATER
			TYPICAL	MAX	GALLONS
					(LITERS)

Control Lock

or

Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.

To turn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The Control Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button while your dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the controls are locked.

NOTE: You may need to disable Sleep Mode by pressing either START/RESUME or CANCEL, or by opening and closing the door before you are able to turn Control Lock off.

To turn off Control Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The light turns off.

NOTE: If your model requires you to press and hold 4 HOUR DELAY to lock the controls, the Control Lock LED will be on or off to indicate if Control Lock is active or not.

CONTROLS AND CYCLE STATUS

CONTROL PURPOSECOMMENTS

To start or resume a wash cycle

If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.

NOTE: If the Start/Resume button is located on top of door, push door firmly closed within 3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds, the Start/Resume button LED will flash, an audible tone will be heard, and the cycle will not start.

To reset any cycle or options during selection.

To cancel a wash cycle after it's started.

Press and hold CANCEL/DRAIN to reset any control selections made.

See “Canceling A Cycle After Dishwasher Is Started” and “Changing A Cycle After Dishwasher Is Started” sections.

	To turn the audible		Press and hold the Hi-Temp Scrub button for 3 seconds to turn the audible tones on or off.
	tones on or off.		Only audible tones for confirming button presses can be turned on/off. Important audible
			tones, such as indicating a cycle has been interrupted, cannot be deactivated.
			Dishwasher Feedback Section
CONTROLS AND CYCLE STATUS
CONTROL		PURPOSE		COMMENTS
		The Cycle Status Indicator		Clean indicator glows when a cycle is finished.
		Lights are used to follow the		If you select the Sani Rinse option, when the Sani Rinse cycle is finished,
		progress of the dishwasher
				the Sanitized indicator glows. If your dishwasher did not properly sanitize
		cycle. Located on the front
				your dishes, the light flashes at the end of the cycle. This can happen if the
		of the dishwasher for front
				cycle is interrupted, or the water could not be heated to the required
		control models, and located
				temperature.
		on the top of the door for
				The Clean and Sanitized lights go off when you open and close the door or
		hidden control models.
				press and hold CANCEL.
	A	The Front Indicator Light or		The light will be blue if the dishwasher is washing or rinsing. The light will
		Single Exterior Light (A)		be red when the dishwasher is drying. The light will be green to indicate
		shows progress of your		that the cycle is complete. If the Front Indicator Light is blinking, see
		dishwasher cycle by color		“Troubleshooting” section.
		(for hidden control models
		only).

The Cycle Status Display is used to follow the progress of the dishwasher cycle, and to show other information.

(Available on some models instead of Cycle Status Indicator Lights)

The indicators will inform you if you are able to add a dish to the cycle after it has started. It will also inform you if the dishwasher is washing, rinsing, drying, complete, and/or sanitized. They will show whether the control is locked and/or the delay option is selected. A series of bars will count down the duration of the cycle remaining from left to right. Each bar equals approximately 24 minutes of cycle length. The bars will also count down the delay feature from left to right, and the delay indicator will be activated.

10