Winegard SS-1000 installation instructions Amplified Model SS-2000 only

AMPLIFIED MODEL SS-2000 ONLY

Attaching Downlead Cable

If using the Power Injector, follow these steps.

STEP 6. Attach the cable coming from your preamp or amplified antenna to the jack on the PS-1503 Power Injector marked “Ant”. See Figure 4.

STEP 7. Attach the cable from your TV set or Distribution Sys- tem to jack on Power Injector marked “TV”. See Figure 4.

STEP 8. Attach supplied 6’ cable between AC Power Adapter and jack on Power Injector marked “Pwr In”. See Figure 4.

EXAMPLE OF ANTENNA

GROUNDING IN

ACCORDANCE WITH THE

NATIONAL ELECTRICAL CODE

INSTRUCTIONS

								Antenna
Ground Clamp							➤	Lead-in Wire
Electrical
					➤
								Antenna Discharge Unit
Service
							➤	(NEC Section 810-21)
Equipment
						➤
➤				➤			Grounding Conductors
							(NEC Section 810-21)
		➤
		➤	Ground Clamps
	➤				Power Service Grounding
	➤

Electrode System

(NEC Art. 250, Part N)

NEC - NATIONAL ELECTRICAL CODE

STEP 9. Insert AC Power Adaptor into 117 VAC wall outlet.

CAUTION:

No splitters or antenna couplers should be installed in the coax line between the antenna and the power supply.

Figure 4

TO PREAMP OR

AMPLIFIED ANTENNA

PS-1503

POWER

ANT.INJECTOR

PS-1503	DOWNLEAD
AC ADAPTOR	COAX
SUPPLIED	TV

POWER IN	CABLE TO TV OR
	DISTRIBUTION AMP
	(SYSTEM)
	LED

6’ CABLE SUPPLIED

15.Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

16.Never push objects of any kind into this video product through openings as they may touch danger- ous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

17.Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18.Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power supply cord or plug is damaged.

b. If liquid has been spilled or objects have fallen into the video product.

c. If the video product, except for antenna mounted preamplifiers and downconverters, has been exposed to rain or water.

d. If the video product does not operate normally by following the operating instructions. Adjust only those controls, when provided, that are covered by the operating instructions. An improper adjustment of other controls may result in damage that will often require extensive work by a qualified technician to restore the video product to its normal operation.

e. If the video product has been dropped or the housing has been damaged.

f. When the video product exhibits a distinct change in performance - this indicates a need for service.

19.When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Improper sub- stitutions may result in fire, electric shock or other hazards.

20.Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

21.Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Art. 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

22.This product should be mounted to a wall or ceiling only as recommended by the manufac- turer.

23.The product should be situated away from heat sources such as radiators, heat registers, stoves or other products (including amplifiers) that produce heat.

6 3