Wolf Appliance Company CT30EU, CT15E, CT36EU manual T R I P L E - Z O N E E L E M E N T

W O L F ELECTRIC COOKTOP U S E & C A R E

COOKTOP O P E R AT I O N

T R I P L E - Z O N E E L E M E N T

To turn on a triple-zone heating element, touch the OFF ON touch pad of the control that corresponds with the triple-zone element. Refer to the illustration below.

Set the heat setting for the inner element zone as described on page 14.

Touch ZONE 2 and the middle element zone will be turned on to the same heat setting as the inner zone. A light will remain on under the ZONE 2 touch pad to indicate the middle element zone is on.

Touch ZONE 3 and the outer element zone will be turned on to the same heat setting as the inner and middle element zones.

A light will remain on under the ZONE 3 touch pad to indicate the outer element zone is on.

Changing the heat setting to the entire triple-zone element is the same as for a single element.

If ZONE 3 is turned on directly, ZONE 2 will automatically be turned on. Similarly, if all three zones are turned on, turning off ZONE 2 will automatically turn off ZONE 3.

When ZONE 3 is turned on, lights under the other two zones will dim. This is normal.

B R I D G E - Z O N E E L E M E N T

When activated, the bridge-zone element creates an oblong heating area for use with a griddle, open roaster or fish poacher.

To turn on the bridge-zone heating element,

touch the OFF ON touch pad of either control that corresponds with the bridge zone element. Refer to illustration below.

Set the heat setting for either the front or rear element as described on page 14.

Touch BRIDGE. The bridge element and the element that is not turned on will both be set to the same heat setting as the first element. Lights will remain on under the front, rear and bridge element touch pads to indicate the bridge-zone elements are on.

Changing the heat setting of the entire bridge-zone element is done the same as for a single element. All three elements maintain the same heat setting.

Touch BRIDGE again to turn off the bridge element. The light under the bridge element touch pad will go out. The front and rear elements will remain at the current heat setting and will become independent of one another.

The illustrations below show the control panel of Model CT36E.

										H
										IG
										H
								N
								O
							F
							F
							O		2
								E
							IM	N
								ZO		3
							S
									E
									N
						H		ZO
						IG
						H
					N					F
					O					F
				F						O
				F
				O	E		H
					G		IG	R
			IM		ID		H	A
					R			E
			S		B	N		L
								C
					O
					F
					F
	H				O				O
IG				IM
H
N				S
O
F
F
O
IM
S
				H
			IG
			H
		N
		O
	F
	F
	O		2
T		E
		N
L		O
E		Z
M
							Dual-zone
							element control

Dual-zone element

Dimensions in parentheses are in millimeters unless otherwise specified.

									H
									IG
									H
							N
							O
						F
						F
						O		2
							E
						IM	N
							ZO		3
						S
								E
								N
					H		ZO
					IG
					H
				N					F
				O					F
			F						O
			F
			O	E		H
				G		IG	R
		IM		ID		H	A
				R			E
		S		B	N		L
							C
				O
				F
				F
H				O				O
IG			IM
H
			S
			H
		IG
		H
	N
	O
F
F
O		2
	E
	N
	ZO
									Triple-zone
									element control

Triple-zone element

										H
										IG
										H
								N
								O
							F
							F
							O		2
								E
							IM	N
								ZO		3
							S
									E
									N
						H		ZO
						IG
						H
					N					F
					O					F
				F						O
				F
				O	E		H
					G		IG	R
			IM		ID		H	A
					R			E
			S		B	N		L
								C
					O
					F
					F
	H				O				O
IG				IM
H
N				S
O
F
F
O
IM
S
				H
			IG
			H
		N
		O
	F
	F
	O		2
T		E
		N
L		O
E		Z
M
							Bridge-zone
							element control

Bridge-zone element

15