Vertical Shaft Seal Replacement (Figure 13)
1.Disconnect and remove the rear driveline from the gearbox.
2.Remove vent plug (24) and siphon gear lube from housing through this opening.
3.Remove crossbar (see page 30).
4.Remove protective seal (8) and vertical shaft seal (18). Replace seal (18) with new seal.
Vertical seal should be recessed in housing. Hori- zontal seal (19) should be pressed flush with out- side of housing.
NOTE: Distortion to seal cage or damage to seal lip will cause seal to leak.
5.Fill gearbox with SAE 80W or 90W gear lube until it runs out the level plug.
6.Remove and replace any seal damaged in installation.
Horizontal Shaft Seal Replacement (Figure 13)
1.Disconnect and remove the rear driveline from the gearbox.
2.Remove vent plug (24) and siphon gear lube from housing through this opening.
3.If the leak occurred at either end of horizontal shaft, remove oil cap (20) and/or oil seal (19). Replace with new one.
4.Fill gearbox with SAE 80W or 90W gear lube until it runs out the level plug.
GEARBOX REPAIR
Removal from Cutter (Figure 13)
NOTE: Gearbox is heavy: do not attempt to move with- out mechanical assistance.
1.Disconnect and remove the rear driveline from the gearbox.
2.Remove cotter pin and nut from vertical shaft and remove crossbar (see page 30).
3.Remove the six bolts that attach gearbox to cutter and remove gearbox.
Disassembly (Figure 13)
1.Remove top cover (22) from gearbox and pour out gear oil.
2.Remove oil cap (20) (to be replaced).
3.Remove snap ring (10) and shim (13) from input shaft (3).
4.Support gearbox in hand press and push on input shaft (3) to remove bearing (7).
5.Remove six cap screws (23) and top cover (22) from housing. Remove gear (1) from inside housing.
6.Remove oil seal (19) from front of housing (to be replaced).
7.Remove snap ring (10) and shim (13) from front of housing (2).
8.Remove input bearing (7) by using a punch and hammer from outside of housing.
9.Support housing in vise in a horizontal position.
10.The castle nut (15), cotter pin (25), and hub are already removed with the stump jumper/crossbar. Remove the protective seal (8), and oil seal (18).
11.Remove cotter pin (9), castle nut (14), and shim (17) from output shaft (4).
12.Remove output shaft (4) by using a punch and hammer and tap on top to drive down. Remove gear (5) and shim (16) from inside housing.
13.Remove bottom bearing (26) by using a punch and hammer from the top, outside the housing.
14.Support housing upside down (top cover surface) and remove bottom bearing (6) by using a punch and hammer from the bottom side of the housing.
15.Inspect gears for broken teeth and wear. Some wear is normal and will show on loaded side. Forged gear surfaces are rough when new. Check that wear pattern is smooth.
16.Inspect vertical and horizontal shafts for grooves, nicks, or bumps in the areas where the seals seat. Resurface any damage with emery cloth.
17.Inspect housing and caps for cracks or other damage.
Assembly (Figure 13)
1.Clean housing, paying specific attention to areas where gaskets will be installed.
2.Wash housing and all components thoroughly. Select a clean area for gearbox assembly. Replace all seals, bearings, and gaskets. All parts must be clean and lightly oiled before reassembling.
3.Insert both output bearings (6) in the housing, using a round tube of the correct diameter and a hand press.
4.Slide output shaft (4) through both bearings (6) until it rests against top bearing (6).
5.Slide shim (16) over output shaft (4).
6.Press gear (5) onto output shaft (4) and secure with shim (17), castle nut (14), and cotter pin (9).
7.Apply grease to lower seal lips (18) and press seal
(18)over output shaft (4), using a tube of the
26 Dealer Service | MAN0707 (5/30/2008) |
|
|
