Be sure operator is familiar with all controls and can stop tractor and cutter quickly in an emergency. The operator should give complete, undivided attention to operating tractor and cutter.

CUTTER OPERATION

When beginning operation of the cutter, make sure that all persons are in a safe location.

Power for operating the cutter is supplied by the tractor PTO. Operate PTO at 540 (1000 RPM for "Q" models).

Know how to stop the tractor and cutter quickly in an emergency.

Engage PTO at a low engine, rpm to minimize stress on the drive system and gearbox.

With PTO engaged, raise PTO speed to 540 or 1000 RPM depending on model and maintain throughout cutting operation.

Gearbox protection is provided by a slip clutch with replacement fiber disc. The slip clutch is designed to slip when excessive torsional loads occur.

Move slowly into material. Adjust tractor ground speed to provide a clean cut without lugging the tractor engine.

Use a slow ground speed for better shredding.

Proper ground speed will depend on the terrain and the material’s height, type, and density.

Normally, ground speed will range from 2 to 5 mph. Tall, dense material should be cut at a low speed; thin, medium-height material can be cut at a faster ground speed.

Always operate tractor PTO at proper RPM (540 or 1000 depending on model) to maintain blade speed and to produce a clean cut.

Under certain conditions tractor tires may roll down some grass and prevent cutting at the same height as the surrounding area. When this occurs, reduce your ground speed but maintain PTO at 540 or 1000 RPM. The lower ground speed will permit grass to rebound partially.

Mowing Tips

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud- denly on slopes.

Use extreme care and reduce ground speed on slopes and rough terrain.

Watch for hidden hazards on the terrain during operation.

CAUTION

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Maximum recommended ground speed for cutting or shredding is 6 miles per hour. Adjust tractor ground speed by using higher or lower gears to provide a clean cut without lugging tractor engine.

Tall material should be cut twice. Cut material higher the first pass. Cut at desired height at 90 degrees the second pass.

Remember, sharp blades produce cleaner cuts and use less power.

Before entering an area, analyze it to determine the best procedure. Consider the height and type of mate- rial to be cut and the terrain type (hilly, level or rough, etc.).

Shredding

The cutter may be used to shred various crops includ- ing green manure, straw, stubble, asparagus residue, corn stalks and similar crops in preparation for tilling. It may also be used to shred pruning in orchards, groves and vineyards.

Each shredding operation may require a different set- up. Start with front edge of cutter high. Adjust up or down as necessary with attitude rod. Experiment until you obtain the results you want.

When shredding attitude is set, check that the distance from the bottom rear edge of the wing to the ground matches the bottom edge of the rear center section to the ground. With the cutting height and attitude estab- lished, adjust the driveline carrier bearing in the H- frame to ensure the front driveline is parallel to the ground.

16 Operation

MAN0707 (5/30/2008)

 

Page 15 Page 17
Page 16
Image 16
Woods Equipment BW180Q-3, BW126-3, BW126Q-3, BW180-3 manual Cutter Operation, Mowing Tips, Shredding
Page 15 Page 17

BW180-3, BW126Q-3, BW126-3, BW180Q-3 specifications

Woods Equipment Company has long been a leader in manufacturing innovative agricultural and landscape maintenance products. Among its popular offerings are the BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models, which are designed to meet the needs of both professional and amateur users.

The BW180-3 is an impressive rotary cutter with a cutting width of 60 inches, making it ideal for tackling overgrown fields, pastures, and other large mowing areas. It features a rugged, all-steel construction that ensures durability and longevity, even in the toughest of conditions. The cutter is equipped with a heavy-duty gearbox, ensuring efficient power transfer while minimizing wear and tear. The innovative design of the BW180-3 also includes an adjustable tail wheel that provides stability and ease of maneuverability.

For those seeking advanced functionality, the BW180Q-3 model introduces quick-attach capabilities, allowing users to easily connect and disconnect the cutter from the tractor without the need for additional tools. This feature not only saves time but also enhances user convenience, making it an excellent choice for busy farms and landscaping operations. With a similar cutting width as the BW180-3, this model maintains the robust construction and drivetrain specifications that make Woods Equipment cutters a trusted choice.

On the smaller side, the BW126-3 offers a 48-inch cutting width, perfect for maintaining smaller fields and lawn areas. Designed with the same enduring quality, it is lightweight yet powerful enough to handle tough mowing tasks. The BW126-3 comes with a versatile hitch design that makes it compatible with a wide range of tractors.

The BW126Q-3 shares the core features of the BW126-3 but incorporates the quick-attach technology for enhanced user efficiency. This model combines flexibility with reliability and is particularly suited for operators who need to switch quickly between attachments throughout their workday.

Overall, the Woods Equipment BW180-3, BW180Q-3, BW126-3, and BW126Q-3 models provide a variety of features and technologies that make them indispensable for anyone looking to efficiently manage land. Whether you need the extra cutting width and power of the BW180 series or the nimble ease of the BW126 series, Woods Equipment offers versatile solutions for diverse agricultural and landscaping needs.
Top Page Image Contents