ATTACHING SWEEPER TO TRACTOR

(Figure 4)

Replace existing step on 2-way angle mount of tractor with shorter step supplied with sweeper. Remove cotter pin on end of step rod and slide out. Install shorter step and replace rod and cotter pin. Keep existing step for use with mower decks if desired.

Attach sweeper mount (2) to the holes in tractor mount- ing bracket (1) that allow the broom mount assembly to set in a level position.

Secure mount to tractor by rotating attaching pins (3) rearward to lock pins into place.

Connect the PTO sleeve and yoke to rectangular shaft of sweeper mount. Attach PTO to shaft on tractor.

Refer to instruction in SweepsterR manual and make sure the broom is level prior to operation.

2-WAY ANGLE WIRING INSTRUCTIONS

(Figure 5)

Position the wiring harness along the right mounting arm of mount, under step, and through the hole in the tractor front panel, directly below the right steering lever. The wiring harness may be separated at the con-

CD4648A

1

1.Tractor mount

2.Sweeper mount

3. Attaching pin

2

nector (A) to ease installation. Disconnect the wiring harness from the tractor at this point when removing the broom from the tractor. Rear section of wiring har- ness may remain on tractor at all times.

Secure relay and connector to tractor frame using plas- tic wire ties through holes near seat hinge.

Attach T-tap securely to a purple wire, directly behind the ignition switch, inside the console. Connect the short black pigtail to the T-tap and install a 7.5 amp auto fuse into the slot. Route the black harness lead into the console through the hole near the seat hinge. Connect the pigtail to the black lead from harness.

Attach eyelet of green wire to negative post of battery. Attach eyelet of red wire with fuse holder to positive post of battery.

Route wires and secure them with wire ties so they are clear of all moving parts of the tractor.

When using the broom for de-thatching, bolt the caster wheel assemblies to each side of the broom head using existing bolts in the broom head. The broom's height can be adjusted by placing spacers on wheel forks above or below the fork housings.

3

Figure 4. Attaching Sweeper to Tractor

MAN0118 (Rev. 12/23/2004)

Assembly 11

 

 

 

Page 12 Page 14
Page 13
Image 13
Woods Equipment FSW6000F, FSW6000T manual Attaching Sweeper to Tractor, WAY Angle Wiring Instructions
Page 12 Page 14

FSW6000F, FSW6000T specifications

Woods Equipment is a renowned manufacturer of high-quality agricultural and landscaping equipment, and the FSW6000F and FSW6000T are prime examples of their commitment to durable, efficient, and innovative design. These flail mowers are engineered to cater to the needs of both professionals and enthusiasts in the agricultural and landscaping sectors.

The FSW6000F is designed specifically for front mount applications, allowing for remarkable maneuverability and visibility. It is equipped with a robust frame that offers stability and durability, ideal for tackling rough terrain. The mower features a heavy-duty hammer blade design which effectively processes tough vegetation, ensuring a clean cut that enhances the aesthetic of any landscape. With a cutting width of 60 inches, it can cover substantial ground in a single pass, increasing productivity and efficiency.

On the other hand, the FSW6000T is a traditional rear mount flail mower that incorporates the same high-quality construction and functionality. This model is perfect for larger open areas where a rear-mounted option is preferred. It boasts an adjustable cutting height, allowing operators to adapt to various mowing conditions and achieve precise results. The dual-direction cutting capability enhances versatility, making it suitable for a wide range of applications from pasture management to roadside maintenance.

Both models utilize advanced technologies, including a unique suspension system that absorbs shocks and vibrations, ensuring a smoother operation and reduced wear on the machine. The heavy-duty rotor design guarantees uniform cutting even at higher speeds, while the efficient belt drive system minimizes power loss and maximizes performance.

Safety is also a priority with Woods Equipment, and both models are equipped with features such as PTO shields, which help to protect operators during operation. The ease of maintenance is another key characteristic, with readily accessible components allowing for quick service and minimal downtime.

In conclusion, the Woods Equipment FSW6000F and FSW6000T flail mowers represent cutting-edge technology and practical design, tailored to meet the rigorous demands of landscape and agricultural work. With their robust features, smart engineering, and superior performance, they stand out as reliable tools for anyone in need of effective mowing solutions.
Top Page Image Contents