![](/images/new-backgrounds/1097150/9715079x1.webp)
TS1680 Pull-Type Assembly (Continued)
FRONT HALF (Figure 29)
Install Tongue
1.Place tongue (1) between mast plates.
2.Place washer (27) and sleeve (19) on cap screw (26).
3.Place washer (27†) between mast plates and tongue, insert cap screw (26) with washer (27†) and sleeve (19) through mast plates, tongue and washer (27†).
4.Secure with washer (27) and lock nut (28).
5.Attach front half of attitude rod (13) to lug on tongue using clevis pin (18) and cotter pin (29).
6.Raise front of cutter and install parking jack (4) to support tongue.
7.Attach safety tow chain (5) to tongue by wrapping chain around diagonal brace and threading the hook end back through the large link on opposite end of chain.
Install CV Driveline (Figure 29)
Install Driveline
3.Attach rear tether chain on driveline to clip on plastic gearbox shield.
H-Frame
1.Attach
2.Place
3.Secure
Attach Driveline to H-Frame
NOTE: Select holes in
Place driveline carrier bearing (8) between
Install CV Drive
1.Slide rear yoke of CV driveline (6) over shaft of driveline (7) and align with notch on shaft.
2.Secure drives together using cap screw (22) and lock nut (21).
Install Drive Shield & Hose Holder
1.Coat input shaft of gearbox with a light coating of grease.
2.Attach slip clutch on driveline (7) to input shaft of gearbox. Tighten cap screws (20) and lock nuts (21).
1.Attach drive shield (11) to driveline carrier bearing using two cap screws (33) and lock washers (32).
2.Attach hydraulic hose holder (15) to the top hole in
1. | Tongue | 21. | 1/2 NC Lock nut |
2. | CV | 22. | 1/2 NC x 2 HHCS GR5 |
3. | 23. | 1/2 NC x | |
4. | Parking jack | 24. | 5/8 NC x 6 HHCS GR5 |
5. | Safety chain | 25. | 5/8 NC Lock nut |
6. | Front 2/3 drive | 26. | 1 NC x 9 HHCS GR5 |
7. | Rear 1/3 drive | 27. | 1" Standard flat washer |
8. | 28. | 1 NC Lock nut | |
11. | Shield | 29. | 1/4 x |
12. | Clevis pin, 1/2 x | 30. | 1/2 NC Flange lock nut |
13. | Attitude rod | 32. | 3/8 Standard lock washer |
14. | 1/2 Schedule 40 x 3.56 pipe | 33. | 3/8 NC x 1 HHCS |
15. | Hose holder | 34. | 1/2 NC x |
16. | Sleeve, 5/8 x 1 x 9/16 | 35. | 1/2 Flat washer |
17. | Cup washer | 36. | 3/8 Flat washer |
18. | Clevis pin, 1 x | 37. | 3/8 x |
19. | Sleeve, 1.02 x 1.38 x .62 | 38. | 3/16 x 1 Cotter pin |
20. | 1/2 NC x 3 HHCS GR5 | + | As required |
|
|
|
|
40Assembly
(Rev. 1/25/2008) MAN0577 (6/29/2007)