6.Remove parking jack from the tongue and attach it to the storage post on the front of the cutter.

7.Adjust H-frame bearing height so that the front driveline is parallel to the ground. Secure with 1/2 x 5-3/4 clevis pin and 3/16 x 1 cotter pin.

8.Attach drive shaft shield to bearing housing using two 3/8 x 1 cap screws and 3/8 lock washers.

Hydraulic Connection

1.Inspect hydraulic hoses to ensure they are in good condition.

2.Clean the fittings before connecting them to the tractor hydraulic ports.

3.Attach the hydraulic hose from the cutter to the tractor.

4.Route the hose through the hose holder on H- frame and be sure the hose can slide freely in the holder. Do not allow hose slack to drag on the ground or become caught on tractor protrusions.

5.From the operator position, start tractor and raise and lower deck several times to purge trapped air from the hydraulic cylinder.

Interference Check

1.Be sure that tractor 3-point lift links do not interfere with hydraulic hoses, cutter driveline, or cutter frame.

2.Check for straight-ahead operation and at full- turning angles. If there is any interference, remove the lower lift links.

3.Contact between tractor lift links and cutter parts can cause damage, especially when turning.

Turning Limits for CV Driveline

You must not exceed a turning angle of 80 degrees at the head of the Constant Velocity driveline or damage will occur.

To check for potential excessive turn angle:

1.Disconnect driveline from tractor, start engine and turn as far right or left as possible.

2.Shut engine off, set parking brake, remove key, and try to connect CV driveline to tractor. If it cannot be connected, the angle is too severe.

3.Restart engine and straighten angle slightly. Repeat step 2 until driveline can be connected. The point at which the driveline can be connected is the maximum turn that should be made.

CONNECT CUTTER TO TRACTOR (MOUNTED)

Tractor Adjustments

Before attaching tractor to cutter, install sway blocks or sway chains, or adjust stabilizer bars. Refer to the trac- tor operator's manual for instructions.

Install tractor front end weights as recommended by the tractor manufacturer to provide 20% of weight on front wheels.

A minimum 20% of tractor and equipment weight must be on the tractor front wheels when attachments are in transport position. Without this weight, tractor could tip over, causing personal injury or death. The weight may be attained with front wheel weights, ballast in tires or front tractor weights. Weigh the tractor and equipment. Do not estimate.

Figure 2. 3-Point Mounting Positions

Category 2 Standard Hitch

1.Position tractor lower lift arms between hitch mast plates.

2.Insert lower hitch pins to Position B, Figure 2, through mast plates and tractor lower lift arms.

3.Secure with lynch pins.

4.Attach top link for mounted units in the middle hole of upper mast using top link pin.

Category 3 Standard Hitch

1.Position tractor lower lift arms between hitch mast plates.

MAN0577 (6/29/2007)

Operation 15

 

 

Page 14 Page 16
Page 15
Image 15
Woods Equipment TS1680Q manual Connect Cutter to Tractor Mounted
Page 14 Page 16

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.
Top Page Image Contents