Manuals / Woodstock / Power Tools / Sander

Woodstock W1751 owner manual Label Placement, Labels List

Models: W1751

1 60

Download 60 pages 32.4 Kb

Page 55

W1751 25" Wide-Belt Sander

Label Placement

Safety Label Placement

The safety labels on this machine warn and indicate how to protect the operator or bystander from machine hazards. The machine owner MUST maintain the original label location and read- ability. If a label is removed or becomes unreadable, REPLACE the label before using the machine. For new labels, contact Woodstock International at (360) 734-3482 or www.shopfox.biz.

	Labels List
REF PART�# DESCRIPTION	REF PART�# DESCRIPTION

800	X1751800	SHOP�FOX�LOGO�PLATE
801	X1751801	DATA�LABEL�(W1751)
802	X1751802	LABEL�(CONTROL�PANEL)
805	XLABEL06	LABEL�(READ�MANUAL)
807	XLABEL13	LABEL�(CONVEYOR�PINCH)
808	XLABEL12	LABEL�(SANDER�KICKBACK)
809	X1751809	LABEL�(BRAKE)
810	X1751810	LABEL�(EMERGENCY)	-	53-
			-	53-

811	XLABEL06	LABEL�(USE�RESPIRATOR/GLASSES)
813	XPAINTSF102	TAN�TOUCH-UP�PAINT�
814	X1751814	BLACK/TAN�TRIM�TAPE
815	XLABEL03	LABEL�(CLOSE�DOOR)	PARTS
819	X1751819	LABEL�(AMP�LOAD�W1751)
823	X1751823	LABEL�(W1751)
824	XLABEL-02	LABEL�(DISCONNECT�POWER)

Image 55

Woodstock W1751 owner manual Label Placement, Labels List

Contents

WIDE-BELT Sander Page Contents Service Woodstock Technical Support IntroductionSpecifications Controls and Features Disconnect machine when cleaning, adjusting or servicing Standard Safety InstructionsKeep stable footing and balance at all times Additional Safety Instructions for Sanders Extension Cords 220V OperationGrounding Unpacking Box ContentsCleaning Machine Machine PlacementPlaten AssemblyHandwheel Crank Ducting Air SupplySanding Belt Tensioning Sanding Belt InstallationPressure Roller Depth and Alignment To adjust the pressure rollers, do these stepsPressure Roller Tension Pressure roller adjusterSanding Belt Start and Stop Buttons Control PanelConveyor Belt Start and Stop Buttons Sanding Load Amp MeterTest Run General OperationTo complete the test run, do these steps Using the Amp Draw Meter Setting Feed SpeedTo change the conveyor belt speed do these steps Emergency Stop Changing Sanding BeltsTo use the emergency stop, do these steps To sand a workpiece, do these steps Using the PlatenBasic Sanding TipOperations Jet Air Flow To adjust the jet air flow, do these stepsBelt tracking knob and lever Belt TrackingBelt Oscillation Speed Belt Tracking procedure on Page 24 or the JetMaintaining Air System Cleaning BeltsGeneral LubricationTo check the condition of the brake pads, do these steps Brake ServiceTo replace the brake pads, do these steps Change the V-belt as follows Changing V-BeltsTo tension the V-belts, do these steps Belt TensionConveyor Belt Tension Tracking Conveyor belt tension Tracking adjustment locationsGauge boards placed under Pressure rollers Pressure RollersTo adjust the belt tracking limit switches, do these steps Belt Tracking Limit SwitchMotor & Electrical TroubleshootingSanding and Results See Figure Electrical Box Component LocationsEmergency Digital amp Power lampW1751 Limit Switch Wiring Diagram W1751 General Wiring Diagram Sanding Motor PART# Description Parts ListConveyor System Conveyortable Upper Contactrollerbase Sanding DrumSystem BALLBEARING6005ZZ Upper Machineframe Parts Air System Parts ListDescription Electrical Connections BoxAccessories Accessories List Labels List Label PlacementWarranty Comments Warranty RegistrationBOX BELLINGHAM, WA