Xantrex Technology 815-2524-02, 815-3524 instruction

TM

SW	3524
SW	3524
FREEDOM	SW
	FREEDOM

FREEDOM	SW
	SW		3524
			3524
	CLEAR	FAULT
		RESET	INVERTER
			ENABLE
			FREEDOM	SW
				SW	3524
					3524

TM

foruse by qualified installers only.

Freedom SW 3524-230 shown.

Freedom SW 230V

Sine Wave Inverter/Chargers

	Installation Guide	guide

	Model Numbers
	Model Numbers	This
	815-3524-02	This
	815-2524-02
	™

Image 1

Xantrex Technology 815-2524-02, 815-3524 manual Freedom SW Sine Wave Inverter/Chargers

Contents

Freedom SW Sine Wave Inverter/Chargers Page This guide for use by qualified Purpose About This Guide Electrical Shock and Fire Hazard Important Safety InstructionsElectrical Shock Hazard Explosion Hazard Fire and Burn Hazard Precautions When Working With Batteries Risk of Damage to the INVERTER/CHARGER Exposure to Chemicals and Gases Hazard Limitations on USE RegulatoryPage Contents Page This guide for use by qualified installers only Page Introduction Materials List Materials List Freedom SW 230V Installation Guide Before You Begin the Installation Installation InformationInstallation Codes Electrical Shock and Fire Hazards Xanbus System About the Xanbus System About the Xanbus System Xanbus-enabled Products and Accessories Two Key Performance Factors Planning the InstallationSize and Length of DC Cables Mounting Location of the Freedom SW AC, DC, and Network Components Planning Preparations Planning Preparations Planning Preparations AC Input AC ComponentsAC Disconnect and Over-Current Protection Device AC Output Distribution Panels AC Wiring Freedom SW Models Batteries DC ComponentsDC Cabling Fire Hazard DC Grounding DC Disconnects and Over-Current DevicesMarine Applications1 To unpack and inspect Heavy Item Tools Installation Tools and MaterialsMaterials Overview Installing the Inverter/Charger Fire and Explosion Hazard Choosing a Location for the Inverter/ChargerHeat Hazard Safe Considerations Mounting the Inverter/ChargerTo mount the inverter/charger Approved Mounting Orientation Orientation? Comment Orientation Approved Mounting Orientation? Comment This guide for use by qualified General AC Wiring Considerations Connecting the AC Input and AC Output WiresFIRE, Electrical SHOCK, and Energy Hazards Correct Batter Polarity will Cause Damage to Connecting AC Input Wires Installing the Inverter/Charger To make the AC output wiring connections Connecting the AC Output WiresEquipment Damage DC Connection Precautions Connecting the DC CablesRecommended Cable Sizes and Lengths and Fuse Size Preparing the Cables Guidelines for Routing the DC Cables Equipment Damage DUE to Reverse Polarity Connecting the DC Cables to the Inverter/ChargerTo connect the DC cables DC Cable Connections To connect the chassis ground Mounting Options Connecting the Battery Temperature Sensor BTS To mount the sensor on the negative battery terminal Mounting to the Negative Battery Terminal BTS port To mount the sensor on the battery case Mounting to the Side of the Battery Case To connect the Freedom SW 230V to the Xanbus network Connecting to the Network Performing Checks Prior to Initial Start-Up Testing in Invert Mode Testing Your Installation Installation Complete Testing in Charge Mode and AC Bypass ModeTo verify that the Freedom SW 230V starts charging Stacking Features Parallel Stacking Connect the stacked system as follows DC Connections for Stacked Inverters Neutral Wiring for Stacked Inverters To configure the system for stacking Configuring System for Stacked Operation Wiring Schematic Search Mode Operation in Parallel StackingDisabling Search Mode on the Master Unit Setting Search Mode on the Slave Unit Calculations Charger Settings in a Dual Freedom SW Configuration Examples To set the Max Chg Rate % setting in each Freedom SW To set the Max Chg Rate % setting in each Freedom SW To set the Max Chg Rate % setting in each Freedom SW Freedom SW Physical Specifications Inverter/Charger Physical Specifications Battery Bank Sizing Battery Information Calculating Battery Size Estimating Battery RequirementsBattery AMP-HOURS Used = AC WATT-HOURS÷10 Watts = Volts × Amps Daily watt-hours needed Battery Bank Sizing Worksheet Battery BanksRestrictions on Motor Size Battery Information Battery Sizing Worksheet Battery Series Connection Battery Cabling and Hook-up Configurations Battery Series-Parallel Connections Environmental Specifications Specifications Inverter Specifications Charger Specifications Transfer and General Specifications To install the drip shield Inverter Drip Shield InstallationShock Hazard Drip Shield Placement Desktop Mount 20 mm No clearance required here Page Page Schneider Electric Solar Inverters USA Inc