338 Appendix C: MIDI
DM2000—Manual de Instrucciones
When this is received, the corresponding effect’s function activates (de-
pending on the effect type).
• This does not activate when the effect type is different.

12.3.20 Parameter change (Key remote)

Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches
the device number included in the SUB STATUS.
This is echoed if [Parameter change ECHO] is ON.
When this is received, the same processing that is executed when the key
specified by Address is pressed (released). (Refer to the PARAMETER
CHANGE PARAMETER NUMBER LIST.)
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.

12.3.21 Parameter change (Remote Meter)

When transmission is enabled by receiving a Request of Remote meter, the
specified meter information is transmitted every 50 msec for 10 seconds.
When you want to transmit meter information continuously, a Request
must be transmitted continuously within every 10 seconds.
Reception
This is echoed if [Parameter change ECHO] is ON.
Transmission
When transmission has been enabled by a Request, the parameter specified
by Address (see PARAMETER CHANGE PARAMETER NUMBER LIST)
will be transmitted on the [Rx CH] channel at 50 msec intervals for a du-
ration of 10 seconds.
Transmission will be disabled if the power is turned off and on again, or if
the PORT setting is changed.
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.
Meter data uses the unmodified DECAY value of the DSP. For the inter-
pretation of the value, refer to the PARAMETER CHANGE PARAMETER
NUMBER LIST.

12.3.22 Parameter request (Remote Meter)

Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches
the device number included in the SUB STATUS.
This is echoed if [Parameter change ECHO] is ON.
When this is received, the parameter specified by Address (refer to PA-
RAMETER CHANGE PARAMETER NUMBER LIST) will be transmitted
on the [Rx CH] at 50 msec intervals for a duration of 10 seconds.
If Address UL= 0x7F is received, transmission of all meter data will be halt-
ed immediately. (disable)
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.

12.3.23 Parameter change (Remote Time Counter)

When transmission is enabled by receiving a Request of Remote Time
Counter, the Time Counter data is transmitted every 50 msec for 10 sec-
onds. When you want to transmit Counter information continuously, a
Request must be transmitted within every 10 seconds.
Reception
This is echoed if [Parameter change ECHO] is ON.
Transmission
When transmission is enabled by receiving a Request, the Time Counter
information is transmitted on [RxCH] channel every 50 msec for 10 sec-
onds.
Transmission will be disabled if the power is turned off and on again, or if
the PORT setting is changed.
If [Parameter Change ECHO] is ON, this message is retransmitted without
change.

12.3.24 Parameter request (Remote Time Counter)

Reception
This is received if [Parameter change RX] is ON and the [Rx CH] matches
the device number included in the SUB STATUS.
This is echoed if [Parameter change ECHO] is ON.
When this is received, the Time Counter information is transmitted on the
[Rx CH] channel every 50 msec for 10 seconds.
When the second byte of Address is received on 0x7F, data transmission
will be halted immediately.
Transmission
If [Parameter Change ECHO] is ON, this message is retransmitted without
STATUS 11110000 F0 System exclusive message
ID No. 01000011 43 Manufacture's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E MODEL ID (digital mixer)
MODEL ID 00000110 7F Universal
ADDRESS 00010010 12 Function call Event
0000aaaa 0a Function
DATA 00000000 00 -
0ddddddd dd Release:0, Press:1
00000000 00 -
0ddddddd dd Destination Effect Number 0 - 7
EOX 11110111 F7 End of exclusive
function Channel
Freeze Play button 0x00 0:Effect1-7:Effect8
Freeze Record button 0x01 0:Effect1-7:Effect8
Auto Pan 5.1 Trigger Button 0x02 0:Effect1-1:Effect2
Auto Pan 5.1 Reset Button 0x03 0:Effect1-1:Effect2
STATUS 11110000 F0 System exclusive message
ID No. 01000011 43 Manufacture's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E MODEL ID (digital mixer)
MODEL ID 00000110 06 DM2000
ADDRESS 00100000 20 Address UU
0aaaaaaa aa Address UL
0aaaaaaa aa Address LU
0aaaaaaa aa Address LL
DATA 0ddddddd dd 0:press, 1:release
EOX 11110111 F7 End of exclusive
STATUS 11110000 F0 System exclusive message
ID No. 01000011 43 Manufacture's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E MODEL ID (digital mixer)
MODEL ID 00000110 06 DM2000
ADDRESS 00100001 21 Address UU
0aaaaaaa aa Address UL
0aaaaaaa aa Address LU
0aaaaaaa aa Address LL
DATA 0ddddddd dd Data1 H
0ddddddd dd Data1 L
:
EOX 11110111 F7 End of exclusive
STATUS 11110000 F0 System exclusive message
ID No. 01000011 43 Manufacture's ID number (YAMAHA)
SUB STATUS 0011nnnn 3n n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E MODEL ID (digital mixer)
MODEL ID 00000110 06 DM2000
ADDRESS 00100001 21 Address UU
0aaaaaaa aa Address UL
0aaaaaaa aa Address LU
0aaaaaaa aa Address LL
DATA 0cccccccccc Count H
0ccccccccCc Count L
EOX 11110111 F7 End of exclusive
STATUS 11110000 F0 System exclusive message
ID No. 01000011 43 Manufacture's ID number (YAMAHA)
SUB STATUS 0001nnnn 1n n=0-15 (Device number=MIDI Channel)
GROUP ID 00111110 3E MODEL ID (digital mixer)
MODEL ID 00000110 06 DM2000
ADDRESS 00100001 22 Remote Time Counter
0000tttt 0t 0:Time Code, 1: Measure, Beat, Clock
DATA 0ddddddd dd Hour / Measure H
0ddddddd dd Min / Measure L
0ddddddd dd Sec / Beat
0ddddddd dd Frame / Clock
EOX 11110111 F7 End of exclusive