Manuals / Brands / Home Audio / CD Player / Yamaha / Home Audio / CD Player

Yamaha EM-202VCD (1), (2), (4), (3), CONNECTIONS, Antenna connection, Note, Notes, Earth rod, 15 m (49 feet), (1) Supplied FM antenna, (3) External FM antenna

1 51

Download 51 pages, 1.11 Mb

CONNECTIONS

ANTENNA

(1)

AM

GND

FM 75Ω

UNBAL.

(2)

ANTENNA

AM

GND

FM 75Ω

UNBAL.

15 m (49 feet)(4)

(3)

7.5 m (25 feet)

Antenna connection(1) Supplied FM antenna

Connect the FM antenna wire to the corresponding terminal and direct the FM antenna wire to the direction where the strongest signal can be received.

(2) Supplied AM loop antenna

Connect the AM loop antenna wires to the corresponding terminals. Position the AM loop antenna for optimum reception. Place the AM loop antenna on a shelf etc., or install it on the rack or wall with screws (not supplied).

Notes

•When static is still heard even after adjusting the position of the AM loop antenna, try reversing the wire connections (from the upper terminal to the lower terminal, and vice versa).

•Do not place the AM loop antenna on the unit. It will result in noise generation, since the unit is equipped with digital electronics. Place the AM loop antenna away from the unit.

(3) External FM antenna

Use an external FM antenna instead of an indoor FM antenna if you need better reception. Consult your dealer.

(4) External AM antennaUse an external AM antenna if you need better reception. Consult your dealer.

Note

When using an external AM antenna, be sure to keep the wire of the AM loop antenna connected.

ANTENNA

AM

GND

or

FM 75Ω

UNBAL.

Earth rod

				ANTENNA
				AM
				GND
EO SIGNAL				75Ω
EO SIGNAL				FM UNBAL.
	VCR	MONITOR
N	OUT	OUT	TV	CENTER	FREQUENCY
			MODE	MODE		STEP
			AUTO	NORMAL	100kHz
			AUTO	NORMAL	50kHz
						FM
			PAL	PHANTOM 9kHz		AM
DEO SIGNAL			NTSC		10kHz	AM
DEO SIGNAL

FREQUENCY STEP switch (China and General models only)

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC supply lead of this unit from the AC outlet.

E-8

Contents

Page SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained Remote control transmitter ● AM loop antenna ● Indoor FM antenna J I H G F E D C B T S LM N O GI F J E K L M N O P 0.2 m – 6 m (8” – 20’) Rear speakers Center speaker Front speakers Subwoofer LD player, etc Monitor TV (General model) To AC Outlet Tape deck, etc To AC Outlet Changes INTRODUCTION CONTENTS Page PRECAUTIONS CARE OF VIDEO CDS (CDS) PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •Pickup NOTE CAUTION FOR CARRYING THIS UNIT CAUTION FOR MOVING THIS UNIT VOLTAGE SELECTOR (General model only) Voltages are 110/120/220/240V AC, 50/60 Hz FEATURES The System c5 speaker Configuration Front L, R: 75W + 75W (6Ω ) RMS Output Power, 10% THD, 1 kHz (See figure 1 on page 3 at the beginning part of this manual.) Switch Jack 3Remote Control Sensor 4USER Button (See figure 3 on page 5 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons 4LEVEL Control Buttons Speaker configuration Speaker placement CONNECTIONS (1) (2) 15 m (49 feet) (4) Connecting speakers (See figure 6 on page 6.) Connecting external components (See figure 7 on page 7.) (See figure 8 on page 8.) (See figure 9 on page 8.) (See figure 0 on page 8.) (See figure A on page 8.) (See figure B on page 8.) (See figure C on page 8.) SPEAKER BALANCE ADJUSTMENT Before operation NORMAL (For 5 speaker configuration): Select this position when you use the center speaker PHANTOM (For 4 speaker configuration): Page Press the OPEN/CLOSE button to open the disc table VIDEO CD PLAYER OPERATION DISC selector buttons CD/Video CD playback 3 Place discs on the trays, label side up *Up to three discs can be loaded on the trays Direct-selectionplayback A. For example, to choose selection Press the “5” button B. For example, to choose selection 12 (1)Press the “+10” button (1)Press the “+10” button To playback a desired track on the disc (Skip search) The beginning of any track can be found automatically 1 Select a disc and begin playback 2 Press the button to advance or button to reverse through the disc Press once for each track to be advanced or reversed Program play You can program up to 20 tracks in any desired order 1 Load discs and close the disc table 2 When in the stop mode, press the PROG button to prepare for programming “PROG” and To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Repeat play modes SINGLE REPEAT (S REP) FULL REPEAT (F REP) When the unit is in the all disc play mode: Random play To cancel the random play Switching the time display [Example] To cancel DIGEST and INTRO operations To get a quick overview of a track or a disc (for Video CDs only) To watch scenes of a selected track on a Video CD To watch the beginning of all tracks on a Video CD RETURN: RETURN button NEXT: NEXT button PREV: PREV 1, 2, 3, 4: Track number input Basic operation Use the remote control transmitter for making Playback Control operations English To stop playback Press and hold the RETURN button for more than 2 seconds To return to a previous screen mode during playback Press the RETURN button once If the disc has index numbers TUNING OPERATION Automatic tuning 3 Press the AUTO/MAN’L button so that “AUTO” appears on the display (In this mode, stations are received in stereo or monaural automatically.) 4 Press the button to tune to a higher frequency, or Preset tuning To store stations (Example: To store a station to A1) 1 Tune in to a desired station (Refer to the previous page for tuning procedure.) Automatic preset tuning When the automatic preset tuning is completed UNIT To record a source to tape USING GRAPHIC EQUALIZER Preset graphic equalizer modes (MUSIC) Mode Feature ROCK Adjusting the graphic equalizer for your desired sound taste *Make adjustment by monitoring the equalizer level indicators on the display 14–27.) Press the equalizer control button once or USING SOUND FIELD PROCESSOR Listening to the music with a sound field effect HALL ARENAKARAOKE LR KARAOKE L 3 STEREO (L ONLY) Adjusting CENTER LEVEL Adjusting REAR LEVEL Adjusting DELAY TIME STORING YOUR OWN PROGRAMS To store 1 Select a desired equalizer mode by pressing the MUSIC button 2 Select a desired sound field program by pressing the PROGRAM button 3 Press the user program MEMORY button KARAOKE OPERATION Singing karaoke 1 Connect one or two microphones to the MIC jack(s) on the front panel 2 Play back a source. (For source playback, refer to page 14–27.) For descriptions of the karaoke modes, see the list below Adjusting the level of echo effect Control range: MIN, 1–9,MAX On the front panel: Press the ECHO button once or more to increase the level Press the ECHO button once or more to decrease the level HOW TO USE THE BUILT-INTIMER Timer play 1 Prepare the source to be played For tuner: Tune in to the station you will listen to ➂ ON TIME/time setting mode ➃OFF TIME/time setting mode To cancel the timer play setting How to make time setting in the ON TIME or OFF TIME mode For the hour: Sleep timer operation This unit can be turned into the standby mode automatically OFF SLEEP ↑ *The SLEEP indicator will light up to indicate that the sleep timer is on To confirm the sleep time setting TROUBLESHOOTING ■ Amplifier section ■ Tuner section ■ Video CD player section ■ Video section ■ General