Manuals / Brands / Home Audio / CD Player / Yamaha / Home Audio / CD Player

Yamaha EM-202VCD (See figure B on page 8.), (See figure C on page 8.), English, VOLUME CONTROL, CARE OF VIDEO CDS (CDS), LISTENING WITH HEADPHONES, Control range

1 51

Download 51 pages, 1.11 Mb

ADJUSTING BRIGHTNESS OF THE DISPLAY

If desired, you can adjust brightness of the display.

1 Press and hold the DISPLAY button for more than 2 seconds so that “DIMMER±0” appears on the display.

2 Holding the DISPLAY button pressed, turn the VOLUME control clockwise to increase or counterclockwise to decrease brightness.

This adjustment can be made even though this unit is in the standby mode.

Control range

When the power is on: ±0 to –6 (Preset value: ±0)

In the standby mode: +3 to –3 (Preset value: ±0)

English

VOLUME CONTROL

(See figure B on page 8.)

Front panel operation

Rotate the VOLUME control clockwise to increase the volume, and counterclockwise to decrease the volume.

Remote control operation

Press the VOLUME + button to increase the volume and the VOLUME – button to decrease the volume.

*Adjusted volume level is shown by the volume level meter and in figures on the display.

LISTENING WITH HEADPHONES

(See figure C on page 8.)

•Be sure that your headphones have a 3.5 mm (1/8”) diameter plug and are between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms.

CARE OF VIDEO CDS (CDS)

•When headphones are connected, the speakers are defeated automatically and you can listen to the sound to be output from the front speakers through headphones. Adjust the VOLUME control for desired volume.

Discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your disc collection and player.

•Do not write on either side of the disc, particularly the non- label side. Signals are read from the non-label side. Do not mark this surface.

•Keep your discs away from direct sunlight, heat and excessive moisture.

•Always hold the discs by the edges. Fingerprints, dirt or water on the discs can cause noise or mistracking. If a disc is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius.

E-11

Contents

Page SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained Remote control transmitter ● AM loop antenna ● Indoor FM antenna J I H G F E D C B T S LM N O GI F J E K L M N O P 0.2 m – 6 m (8” – 20’) Rear speakers Center speaker Front speakers Subwoofer LD player, etc Monitor TV (General model) To AC Outlet Tape deck, etc To AC Outlet Changes INTRODUCTION CONTENTS Page PRECAUTIONS CARE OF VIDEO CDS (CDS) PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •Pickup NOTE CAUTION FOR CARRYING THIS UNIT CAUTION FOR MOVING THIS UNIT VOLTAGE SELECTOR (General model only) Voltages are 110/120/220/240V AC, 50/60 Hz FEATURES The System c5 speaker Configuration Front L, R: 75W + 75W (6Ω ) RMS Output Power, 10% THD, 1 kHz (See figure 1 on page 3 at the beginning part of this manual.) Switch Jack 3Remote Control Sensor 4USER Button (See figure 3 on page 5 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons 4LEVEL Control Buttons Speaker configuration Speaker placement CONNECTIONS (1) (2) 15 m (49 feet) (4) Connecting speakers (See figure 6 on page 6.) Connecting external components (See figure 7 on page 7.) (See figure 8 on page 8.) (See figure 9 on page 8.) (See figure 0 on page 8.) (See figure A on page 8.) (See figure B on page 8.) (See figure C on page 8.) SPEAKER BALANCE ADJUSTMENT Before operation NORMAL (For 5 speaker configuration): Select this position when you use the center speaker PHANTOM (For 4 speaker configuration): Page Press the OPEN/CLOSE button to open the disc table VIDEO CD PLAYER OPERATION DISC selector buttons CD/Video CD playback 3 Place discs on the trays, label side up *Up to three discs can be loaded on the trays Direct-selectionplayback A. For example, to choose selection Press the “5” button B. For example, to choose selection 12 (1)Press the “+10” button (1)Press the “+10” button To playback a desired track on the disc (Skip search) The beginning of any track can be found automatically 1 Select a disc and begin playback 2 Press the button to advance or button to reverse through the disc Press once for each track to be advanced or reversed Program play You can program up to 20 tracks in any desired order 1 Load discs and close the disc table 2 When in the stop mode, press the PROG button to prepare for programming “PROG” and To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Repeat play modes SINGLE REPEAT (S REP) FULL REPEAT (F REP) When the unit is in the all disc play mode: Random play To cancel the random play Switching the time display [Example] To cancel DIGEST and INTRO operations To get a quick overview of a track or a disc (for Video CDs only) To watch scenes of a selected track on a Video CD To watch the beginning of all tracks on a Video CD RETURN: RETURN button NEXT: NEXT button PREV: PREV 1, 2, 3, 4: Track number input Basic operation Use the remote control transmitter for making Playback Control operations English To stop playback Press and hold the RETURN button for more than 2 seconds To return to a previous screen mode during playback Press the RETURN button once If the disc has index numbers TUNING OPERATION Automatic tuning 3 Press the AUTO/MAN’L button so that “AUTO” appears on the display (In this mode, stations are received in stereo or monaural automatically.) 4 Press the button to tune to a higher frequency, or Preset tuning To store stations (Example: To store a station to A1) 1 Tune in to a desired station (Refer to the previous page for tuning procedure.) Automatic preset tuning When the automatic preset tuning is completed UNIT To record a source to tape USING GRAPHIC EQUALIZER Preset graphic equalizer modes (MUSIC) Mode Feature ROCK Adjusting the graphic equalizer for your desired sound taste *Make adjustment by monitoring the equalizer level indicators on the display 14–27.) Press the equalizer control button once or USING SOUND FIELD PROCESSOR Listening to the music with a sound field effect HALL ARENAKARAOKE LR KARAOKE L 3 STEREO (L ONLY) Adjusting CENTER LEVEL Adjusting REAR LEVEL Adjusting DELAY TIME STORING YOUR OWN PROGRAMS To store 1 Select a desired equalizer mode by pressing the MUSIC button 2 Select a desired sound field program by pressing the PROGRAM button 3 Press the user program MEMORY button KARAOKE OPERATION Singing karaoke 1 Connect one or two microphones to the MIC jack(s) on the front panel 2 Play back a source. (For source playback, refer to page 14–27.) For descriptions of the karaoke modes, see the list below Adjusting the level of echo effect Control range: MIN, 1–9,MAX On the front panel: Press the ECHO button once or more to increase the level Press the ECHO button once or more to decrease the level HOW TO USE THE BUILT-INTIMER Timer play 1 Prepare the source to be played For tuner: Tune in to the station you will listen to ➂ ON TIME/time setting mode ➃OFF TIME/time setting mode To cancel the timer play setting How to make time setting in the ON TIME or OFF TIME mode For the hour: Sleep timer operation This unit can be turned into the standby mode automatically OFF SLEEP ↑ *The SLEEP indicator will light up to indicate that the sleep timer is on To confirm the sleep time setting TROUBLESHOOTING ■ Amplifier section ■ Tuner section ■ Video CD player section ■ Video section ■ General