Yamaha GX-70 General information, Recording from the built-intuner, English, OTHER RECORDINGS, To stop recording, To stop recording temporarily

OTHER RECORDINGS

1

MINI COMPONENT SYSTEM	DISC CHANGE
GX–70

OPEN/CLOSE

1

General information

• When recording important selections, be sure to make a
	preliminary test to ensure that the desired source material
•	is being properly recorded with good sound quality.
	The automatic recording level control circuit automatically
•	controls the level of the input signal used for recording.
	Adjusting the VOLUME control has no effect on the
	recorded sound.
	If, however, the built-in graphic equalizer and/or sound
	field processor is used, its effect is recorded along with
	the source.

English

2

DISC

PROGRAM

3

PS/PTY/RT/CT

FREQ

RANDOM

PRESET/TUNING/BAND A/B/C/D/E

SEEK		DISPLAY
PTY
	START
MODE	EDIT
REPEAT

VOLUME

* Music with an equalizer effect is suitable for listening to

inside a car etc.

USER

POWER

MUSIC

PHONES

	CD
		DOWN
INPUT	INPUT
DOWN		UP
MEMORY
TAPE 1/2
REC/PAUSE		NORMAL
MODE
DOLBY NR		HIGH
TIMER REC		DUBBING
AUTO/MAN’L		MEMORY
TIMER		TIME ADJ
HOUR		MIN

PLAYBACK 1 2 REC/PLAYBACK

UP

Active Servo

Technology

• For the tape deck, the deck which can be used for

recording is deck 2 only. When recording, be sure to load

a tape into the deck 2 cassette compartment.

Recording from the built-in tuner

EJECT EJECT

4 5 6, 1 3

			CD
7, 2	1	2	3	4	5
	1	2	3	4	5
	6	7	8	9	0
	6	7	8	PRESET
	A	B	C	D	E
	TIME	PROG	TAPE	EDIT	+I0	1
	MODE	REPEAT	RANDOM	OPEN/CLOSE	TUNER
	DISC SKIP			STOP	PLAY/PAUSE
6, 1	REC/PAUSE	TAPE 1/2	PLAY	STOP	PLAY
	CENTER/REAR	TEST	FLAT	TAPE
	/DELAY
	LEVEL		MUSIC	PROGRAM	USER
	SLEEP		POWER		INPUT

VOLUME

1	Press the INPUT selector or		button once or more
	so that “TUNER” appears on the display.
2	Tune to the desired station. (Refer to the “TUNING
	OPERATION” on page 24 and 25.)
3	Load a tape into the deck 2 cassette compartment.
4	When recording with the Dolby NR system, press the
	DOLBY NR button so that “		B” lights up on the display.
	If not, turn it off.
	* For details, refer to the “Dolby B Type Noise
	Reduction” on page 31.
5	Select the reverse mode “		” to record on only one
	side, or “	” for continuous recording on both sides by
	pressing the reverse MODE selector button.
6	Press the REC/PAUSE button.
	* “REC” lights up on the display.

7 Press the play button on the remote control transmitter

to record on side A, or the play button to record on side B.

*For continuous recording on both sides, begin on side A. Recording stops automatically at the end of side B.

To stop recording temporarily

1 Press the REC/PAUSE button.

2 To resume recording, press the play button.

To stop recording

Press the stop button.

To reduce beats during recording

While recording an AM (long wave) broadcast, you may hear a bleep caused by beat frequencies. In such a case, pressing the TUNER input selector button on the remote control transmitter once or more will reduce or remove beats. (Whenever the TUNER input selector button is pressed, “B.C–1” and “B.C–2” appears on the display alternately. Select either of them in which you find that beats are more reduced.)

E-41