REMOTE CONTROL FEATURES

Programming a New Remote

Control Function (Learn Feature)

If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so the buttons are programmable independently for each source component area.

Note

•This remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of the other remote control’s functions. However, you may not be able to program some special signals or extremely long transmissions. (Refer to the operation instructions for the other remote control.)

1 Press an input selector button or Å to select a source component.

SYSTEM

STANDBY

 

6CH INPUT

POWER

SLEEP

A

PHONO

TUNER

CD

V-AUX

CBL/SAT

MD/TAPE

CD-R

D-TV/LD

VCR 1

VCR2/DVR

DVD

4 Press the button for which you want to program the new function.

“LEARN” is displayed.

 

 

SKIPDISC

REC

TV

POWER

 

D

AUX

A

SYSTEM POWER

TRANSMIT

 

 

 

TV/LD

 

 

 

 

 

 

 

-

V

 

 

 

 

 

 

 

 

 

 

 

-

 

 

 

 

 

 

 

 

 

 

1 VCR

CBL/SAT

PHONO

STANDBY

CLEAR NAME–RE

 

 

AUDIO

 

AV

POWER

 

VCR2/DVR

MD/TAPE

TUNER

SLEEP

–

VOL

+

 

 

AMP

SELECT

DVD

R-CD

CD

INPUT 6CH

LEARN

5 Press and hold the button on the other remote control that has the function you want to program into this remote control until “OK” appears in the display window.

TV

POWER

 

D

AUX

A

SYSTEM POWER

TRANSMIT

 

TV/LD

 

 

 

-

V

 

 

 

 

 

 

 

-

 

 

 

 

 

 

1 VCR

CBL/SAT

PHONO

STANDBY

CLEAR NAME–RE

AV

POWER

 

VCR2/DVR

MD/TAPE

TUNER

SLEEP

 

AMP

SELECT

DVD

R-CD

CD

INPUT 6CH

LEARN

2 Place this remote control and the other remote control 1 to 4 cm apart on a flat surface so that their infrared transmitters are aimed at each other.

TV

POWER

 

D

AUX

A

SYSTEM POWER

TRANSMIT

 

TV/LD

 

 

 

-

V

 

 

 

 

 

 

 

-

 

 

 

 

 

 

1 VCR

CBL/SAT

PHONO

STANDBY

CLEAR NAME–RE

AV

POWER

 

VCR2/DVR

MD/TAPE

TUNER

SLEEP

 

AMP

SELECT

DVD

R-CD

CD

INPUT 6CH

LEARN

1 to 4 cm (approximately 1 inch)

3 Press LEARN by using a ballpoint pen or similar object.

Do not press and hold LEARN longer than three seconds. Otherwise this unit enters the manufacturer code setting mode.

LEARN

Flashes alternately

Note

•If you do not press any button within 30 seconds during steps 5 and 6, the learning process is canceled. If this happens, start

over from step 4.

Notes

•“NG” appears in the display window when programming has not been done correctly. In this case, start over from step 4.

•This remote control can learn approximately 120 functions. However depending on the signals learned, “FULL” may appear in the display window much earlier than this number. In this case, clear unnecessary programmed functions to make further learning on the remote control.

6 Repeat steps 4 and 5 to program additional functions.7 Press LEARN again to exit from the learning mode.

LEARN

Notes

•Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to this remote control.

•When the remote controls are either too close together or too far apart, you may not be able to program this remote control.

•Direct sunlight interferes with infrared rays.

•“ERROR” appears in the display window when pressing more than one button at once.

44