TROUBLESHOOTING

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, set this unit in the standby mode, disconnect the power cord, and contact the nearest authorized YAMAHA dealer or service center.

■General
ProblemCauseRemedyRefer

 

 

 

to page

 

 

 

 

This unit fails to turn

The power cord is not connected or the

Firmly connect the power cord.

19

on when STANDBY/

plug is not completely inserted.

 

 

ON (or SYSTEM

 

 

 

 

 

 

POWER) is pressed,

The IMPEDANCE SELECTOR switch

Set the switch fully to the left or right position when

19

or enters in the

on the rear panel is not fully set to the

this unit is in the standby mode.

 

standby mode soon

left or right position.

 

 

after the power has

 

 

 

 

 

 

been turned on.

The protection circuitry has been

Make sure all speaker wire connections on this unit

12, 13

 

activated.

and on all speakers are secure and that the wire for

 

 

 

each connection does not touch anything other than

 

 

 

its respective connection.

 

 

 

 

 

On-screen display

The setting for the on-screen display is

Select the full display or short display mode.

21

does not appear.

set to “DISPLAY OFF”.

 

 

 

 

 

 

 

The BLUE BACK setting under “9

Set BLUE BACK to AUTO to always show the

62

 

DISPLAY SET” on the SET MENU is

OSD.

 

 

set to OFF, and no video signal is input

 

 

 

to this unit.

 

 

 

 

 

 

No sound and/or no

Incorrect input or output cable

Connect the cables properly. If the problem persists,

11 – 17

picture.

connections.

the cables may be defective.

 

 

 

 

 

 

An appropriate input source has not been

Select an appropriate input source with INPUT l/

25

 

selected.

hor 6CH INPUT (or the input selector buttons).

 

 

 

 

 

 

The speaker connections are not secure.

Secure the connections.

12, 13

 

 

 

 

 

The main speakers to be used have not

Select the main speakers with SPEAKERS A and/or

25

 

been selected properly.

B.

 

 

 

 

 

 

The volume is turned down.

Turn up the volume.

26

 

 

 

 

 

The sound is muted.

Press MUTE or any operation buttons of this unit to

26

 

 

cancel a mute and adjust the volume.

 

 

 

 

 

 

Digital signals other than PCM audio,

Play a source whose signals this unit can reproduce.

—

 

Dolby Digital or DTS signal which this

 

 

 

unit cannot reproduce are being input to

 

 

 

this unit by playing a CD-ROM, etc.

 

 

 

 

 

 

The picture does not

The output and input for the picture are

Make connections using the same type of jack

14, 15

appear.

connected to different types of video

(between composites, S-VIDEOs, or components)

 

 

jacks.

for both the input and output.

 

 

 

 

 

The sound suddenly

The protection circuit has been activated

Check the IMPEDANCE SELECTOR switch is set

13

goes off.

because of a short circuit, etc.

to the appropriate position and then turn this unit

 

 

 

back on.

 

 

 

 

 

 

 

Check the speaker wires are not touching each other

12, 13

 

 

and then turn this unit back on.

 

 

 

 

 

 

The sleep timer has functioned.

Turn on the power, and play the source again.

64

 

 

 

 

 

The sound is muted.

Press MUTE or any operation buttons of this unit to

26

 

 

cancel a mute and adjust the volume.

 

 

 

 

 

INFORMATION

ADDITIONAL

 

 

English

71