Yamaha P50-m Changing the Device Number, 1. 2.

19

OPERATION GUIDE

● When Program Change Table is set to “oFF”

The P50-m does not respond to XG System On or GM Mode On

messages.

● When Program Change Table is set to “on”

The P50-m responds to XG System On or GM Mode On messages and

performs the following:

•Resets all controllers to default or “zero” values.

•Selects Voice number 9 (the Voice most similar to GM voice 001,

Grand Piano).

•Parameters of all voices are set to the same values as the Voice

number 9 (Grand Piano).

•Sets Reverb Send of selected Voice to 040.

•Sets Transpose to 00.

Changing the Device Number

Device Number is a kind of MIDI “identification” number. This is

convenient when using two or more P50-m units together in a

MIDI chain. It is also important when sending System Exclusive

data. When each unit in a chain is assigned a different Device

Number, the controlling MIDI device can distinguish between

different units.

The “ALL” setting allows the P50-m to respond to all 16

Device Numbers. For normal operation, this should be set to

“ALL.”

Settings: 01 — 16, ALL

1. Double-click the TOUCH button (press it twice quickly).

2. Use the DATA dial to change the Device Number setting.

Double-click.

Lamp flashes.

Device Number setting.

Contents

Main FCC INFORMATION (U.S.A) * NEDERLAND NETHERLAND ADVARSEL! VARNING VAROITUS SPECIAL MESSAGE SECTION PLEASE KEEP THIS MANUAL Welcome to the P50-m Unpacking iii Table of Contents OPERATION GUIDE APPENDIX SOUND LISTS & MIDI DATA How to Use This Manual 1) Precautions 2) The Controls of the P50-m 3) Setting Up and Playing Your P50-m 4) Operation Guide Precautions LOCATION USE THE CORRECT POWER ADAPTOR MAKE SURE POWER IS OFF WHEN MAKING OR REMOVING CONNECTIONS HANDLE THE INSTRUMENT WITH CARE Page The Controls of the P50-m Front Panel TONE Controls TUNE Controls UTILITY Controls Rear Panel Setting Up and Playing Your P50-m What Youll Need 2. 1. An amplifier/speaker system, preferably stereo. Alternately, you Page Using in Larger MIDI Systems Powering Up and Playing the Demo Song Page Playing all Demo Songs Operation Guide Voice Controls Selecting a Voice 1. 2. Page Tone Controls Changing the Brightness of a Voice 1. 2. Page Page Tune Controls Changing the Master Tune Setting 1. 2. Page Utility Controls Changing the Touch Sensitivity 1. 2. Changing the MIDI Receive Channel 1. 2. Advanced Functions Program Change Table 2. 1. Changing the Device Number 1. 2. Page Changing the MIDI OUT Setting all 2. 1. Factory Set APPENDIX Troubleshooting Page Error Messages Specifications Index Page Page 30 Voice List Effect Lists Effect Type List REVERB CHORUS WHITE ROOM, TUNNEL, BASEMENT Effect-Data Assignment Table table#1 LFO Frequency (Hz) table#2 Modulation Delay Offset (msec) table#3 EQ Frequency (Hz) table#4 Reverb Time (sec) MIDI Data Format 1. Channel voice messages 1.1 Note Off 1.2 Note On / Note Off 1.3 Polyphonic Aftertouch 34 1.5 Program Change 1.6 Channel Aftertouch 1.7 Pitch Bend Change 2. Channel Mode Messages 2.1 All Sound Off 2.2 Reset All Controllers 2.3 All Note Off 2.4 Omni Off 36 3.2 Bulk Dump 4. Realtime Messages 4.1 Active Sensing 5. MIDI thru out 5.1 When MIDI OUT=ot1 5.2 When MIDI OUT=ot2 38 < Table 1-2 > MIDI Parameter Change table ( SYSTEM ) [XG] < Table 1-3 > MIDI Parameter Change table ( EFFECT 1) [XG] < Table 1-4 > MIDI Parameter Change table ( PART ) [XG] 40 < Table 2-2 > MIDI Parameter Change table ( SYSTEM ) [P50-m] Parameter Change Address (H) (M) (L) Address P50-m SYSTEM 00 00 00 < Table 2-1> < Table 2-3 > MIDI Parameter Change table ( REMOTE SWITCH ) [P50-m] MIDI Implementation Chart