Manuals / Brands / Home Audio / Stereo Receiver / Yamaha / Home Audio / Stereo Receiver

Yamaha RX-V1000RDS TUNING, Connecting the Antennas, ■Connecting the AM loop antenna, ■Connecting the indoor FM antenna, strength, 3Release the tab to lock the lead wires

1 85

Download 85 pages, 2.16 Mb

TUNING

Connecting the Antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal

strength.Connect each antenna correctly to the designated terminals.

AM loop antenna

	(included)	Indoor FM
		antenna
	(Europe model)
		(included)

DIGITAL OUTPUT

MD/TUNER

TAPE

AM

CD-R ANT

OPTICAL GND

CD

CD-R

75 UNBAL.

FM

ANT

DVD

GND

D-TV

/LD

OPTICAL

COAXIAL

RS-

CD 232C

CBL /SAT

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND

DIGITAL INPUTterminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

3Release the tab to lock the lead wires.Lightly pull the lead wires to confirm a good connection.4Attach the loop antenna to the antenna stand.5Orient the AM loop antenna so that the best reception is obtained.

y

•The AM loop antenna can be removed from the stand and attached to a wall, etc.

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

A properly installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about the outdoor antennas.

■Connecting the indoor FM antennaConnect the included indoor FM antenna to the 75Ω UNBAL. FM ANT terminal.

Note

•Do not connect an outdoor FM antenna and the indoor FM antenna at the same time.

■Connecting the AM loop antenna

21

4	3	5

Connecting a coaxial cable to the included75-ohm/300-ohm antenna adapter (U.K. model only)

1	2	(7/16)
	11	(7/16)
	8	(5/16)	Unit:
Cover	6	(1/14)	mm (inch)
Cover
Open the cover of the	Cut the external sleeve of
included 75-ohm/300-ohm	the 75-ohm coaxial cable
antenna adapter.	and prepare it for
3	connection.
3

Lead wire

Cut the lead wire and remove it.

Antenna stand

1Press and hold the tab to unlock the terminal hole.2Insert the AM loop antenna lead wires into the AM ANT and GND terminals.

4	5
Clamp	Clamp with
with	pliers.
pliers.
	Insert the wire
	into the slot.

Insert the cable wire into the slot, and clamp it with pliers.

Snap the cover into place.

30

Contents

Natural Sound AV Receiver Ampli-tuner audio-vidéo CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Installing Batteries in the Remote CONTROLS AND FUNCTIONS qREC OUT wEFFECT eA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control 1 A e r t y sdf g h 1Infrared window 2TRANSMIT indicator 3STANDBY 4SYSTEM POWER 5Input selector buttons Using the Remote Control ■Handling the remote control Front Panel Display 6 7 8 90 q e r t y i op 1 t indicator Rear Panel 1DIGITAL INPUT jacks 2DIGITAL OUTPUT jacks 3Antenna input terminals 4Audio component jacks SPEAKER SETUP CONNECTIONS Connecting Audio Components Page Connecting Video Components ■About the video jacks ■Video monitor with a 21-pinconnector ■VIDEO AUX jacks (on the front panel) Page Connecting the Speakers ■Speaker cables 1 Remove approx. 10 mm (3/8”) of insulation from each of the speaker cables 2 Twist the exposed wires of the cable together ■Using the rear center speaker Rear center speaker placement Connecting the rear center speaker Setting up this unit for using the rear center speaker Connecting to an External Amplifier 5SUBWOOFER jack this unit 1MAIN jacks IMPEDANCE SELECTOR Switch WARNING Connecting the Power Supply Cords ■AC OUTLET(S) (SWITCHED) ON-SCREENDISPLAY (OSD) P01 CONCERT HALL SPEAKER MODE SETTINGS ADJUSTING THE SPEAKER OUTPUT LEVELS Using the Test Tone (TEST DOLBY SUR.) Use the test tone to balance the output levels of the 1,5 1Press TEST to output the test tone BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■BGV (background video) function Input Modes and Indications AUTO: In this mode, the input signal is automatically selected in the following ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program ■Virtual CINEMA DSP and SILENT CINEMA DSP –when the 6ch Stereo, DOLBY DIGITAL/Normal or DTS/ Normal program is selected; –when the sound effect is turned off; –when 6CH INPUT is selected as the input source; –when 96-kHzsampling digital signals are input to this unit; TUNING Automatic (or Manual) Tuning 1 Press INPUT l / h to select TUNER as the input source 2Press FM/AM to select the reception band Presetting Stations ■Automatically presetting stations (for RDS stations) 1Press FM/AM to select the FM band 3Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds Automatic preset tuning options ■ Manually presetting stations 5 Press MEMORY (MAN’L/AUTO FM) while the You can also store up to 40 stations (8 stations x “MEMORY” indicator is flashing groups) manually Exchanging Preset Stations 2,4 1Tune in to preset station “E1” 2Press and hold PRESET/TUNING (EDIT) for more than 3 seconds 3Tune in to preset station “A5” by using the buttons on the front panel RECEIVING RDS STATIONS PTY SEEK Function 1 Press PTY SEEK MODE to set the unit in the PTY SEEK mode ■To cancel this function ■Program types in the PTY mode EON Function 1Make sure that the “EON” indicator lights up on the front panel display The selected program type name indicator lights up on the front panel display BASIC RECORDING SET MENU SET MENU 1/4 2 LOW FRQ TEST 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D REAR CT SP 1E LFE/BASS OUT 1F MAIN LEVEL 3 L/R BALANCE (balance of the left and right main speakers) Control range: 10 steps for L/R Initial setting: 4 HP TONE CTRL (headphone 10 DOLBY D. SET (Dolby Digital 11 DTS LFE LEVEL This setting is effective only when this unit decodes DTS signals Control range (dB): –10to +10 12 6.1/ES AUTO Choices: ON, OFF 14 DISPLAY SET ■BLUE BACK > AUTO/OFF ■OSD SHIFT (OSD off-setposition) This setting is used to adjust the vertical position of the OSD ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER REMOTE CONTROL FEATURES ■SOURCE SELECT k / n ■OPTN (option) area Each Component Control Area The YAMAHA code is factory set for the A, TUNER, MD/TAPE, CD ■Operating a tuner (TUNER area) ■Operating a CD player (CD area) When the manufacturer code for your TV is set up in the both ■Operating an MD recorder (MD/TAPE area) ■Operating a CD recorder (CD-Rarea) ■Operating an LD player (A area) ■Operating a DVD player (DVD area) ■ Operating a VCR (VCR 1, VCR 2/DVR and V-AUXareas) ■Operating a TV/digital TV (D-TV/LDand PHONO areas) If you operate an LD player in the ■Operating a cable TV (CBL/SAT area) or satellite tuner (B area) ■Free area (OPTN area) Setting the Manufacturer Code 3Press k / n to select the name of your component’s manufacturer If the component cannot be controlled with the remote / control, try setting another code for the same manufacturer Programming a New Remote Control Function (Learn Feature) 1 Set 10KEY/DSP to 10KEY 2Press an input selector button, A or B to select a source component 4Press LEARN by using a ballpoint pen or similar object 7Repeat steps 5 and 6 to program additional functions 8Press LEARN again to exit from the learning mode 5Press the button for which you want to program the new function “LEARN” is displayed Using the Macro Feature ■Operating the macro 1Set MACRO ON/OFF to ON 2Press a macro button •When you have finished using the Macro feature, set MACRO ON/OFF to OFF ■Programming a macro Changing the Source Name in the Macros, Renamed Source Names SOUND FIELD PROGRAM CINEMA DSP Programs ■For audio-videosources: Nos. 7 to Game This program adds a deep and spatial feeling to video game sounds TV SPORTS (group) 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds MOVIE THEATER Programs ■Dolby Pro Logic + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect SOUND FIELD PROGRAM PARAMETER EDITING Sound Field Program Parameters P05 ROCK CONCERT Digital Sound Field Parameter Descriptions ■INIT.DLY (initial delay) (P.INIT.DLY — for the presence sound field) Function: direct sound and the first reflection heard by the listener ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RC.DELAY (rear center delay) TROUBLESHOOTING Page English APPENDIX ■Tuner ■Remote control SPECIFICATIONS Page Quick Reference Card ■Remote Control ■TUNER ■CD ■MD ■ LD (A) ■ VCR ■ DVD ■ TV (TV/LD) ■CBL/SAT (CBSAT)