Yamaha RX-V1000RDS ■Tuner

TROUBLESHOOTING

■Tuner

	Problem	Cause	Remedy	Refer to
	Problem	Cause	Remedy	page
				page

	FM stereo reception	The characteristics of FM stereo broadcasts	Check the antenna connections.	30, 31
	is noisy.	may cause this problem when the	Try using a high-quality directional FM
		transmitter is too far away or the antenna	antenna.
		input is poor.	Use the manual tuning method.

	There is distortion,	There is multipath interference.	Adjust the antenna position to eliminate	30
	and clear reception		multipath interference.
	cannot be obtained
FM	even with a good FM
FM	antenna.

	The desired station	The station is too weak.	Use the manual tuning method.	30, 31
	cannot be tuned in		Use a high-quality directional FM antenna.
	with the automatic
	tuning method.

	Previously preset	The unit has been disconnected for a long	Re-store the stations.	32
	stations can no	period.
	longer be tuned in.

	The desired station	The signal is weak or the antenna	Tighten the AM loop antenna connections	30, 31
	cannot be tuned in	connections are loose.	and orient it for best reception.
	with the automatic		Use the manual tuning method.
	tuning method.

	There are continuous	Noises result from lightning, fluorescent	Use an outdoor antenna and a ground wire.	30
AM	crackling and hissing	lamps, motors, thermostats and other	This will help somewhat, but it is difficult to
	noises.	electrical equipment.	eliminate all noise.

	There are buzzing	A TV set is being used nearby.	Move this unit away from the TV.	—
	and whining noises
	(especially in the
	evening).

78

Contents

Natural Sound AV Receiver Ampli-tuner audio-vidéo CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Installing Batteries in the Remote CONTROLS AND FUNCTIONS qREC OUT wEFFECT eA/B/C/D/E Selects one of the 5 preset station groups (A to E) ■Opening and closing the front panel door Remote Control 1 A e r t y sdf g h 1Infrared window 2TRANSMIT indicator 3STANDBY 4SYSTEM POWER 5Input selector buttons Using the Remote Control ■Handling the remote control Front Panel Display 6 7 8 90 q e r t y i op 1 t indicator Rear Panel 1DIGITAL INPUT jacks 2DIGITAL OUTPUT jacks 3Antenna input terminals 4Audio component jacks SPEAKER SETUP CONNECTIONS Connecting Audio Components Page Connecting Video Components ■About the video jacks ■Video monitor with a 21-pinconnector ■VIDEO AUX jacks (on the front panel) Page Connecting the Speakers ■Speaker cables 1 Remove approx. 10 mm (3/8”) of insulation from each of the speaker cables 2 Twist the exposed wires of the cable together ■Using the rear center speaker Rear center speaker placement Connecting the rear center speaker Setting up this unit for using the rear center speaker Connecting to an External Amplifier 5SUBWOOFER jack this unit 1MAIN jacks IMPEDANCE SELECTOR Switch WARNING Connecting the Power Supply Cords ■AC OUTLET(S) (SWITCHED) ON-SCREENDISPLAY (OSD) P01 CONCERT HALL SPEAKER MODE SETTINGS ADJUSTING THE SPEAKER OUTPUT LEVELS Using the Test Tone (TEST DOLBY SUR.) Use the test tone to balance the output levels of the 1,5 1Press TEST to output the test tone BASIC PLAYBACK To select a source connected to the 6CH INPUT jacks 4Start playback (or select a broadcast station) on the source component Refer to the operation instructions for the component 5Adjust the volume to the desired output level ■To mute the sound Press MUTE on the remote control To restore the audio output to the previous volume level, press MUTE again •You can also cancel mute to press any operation buttons such as VOLUME +/– ■BGV (background video) function Input Modes and Indications AUTO: In this mode, the input signal is automatically selected in the following ■Notes on playing a source encoded with a DTS signal ■Notes on playing an LD source Selecting a Sound Field Program ■Virtual CINEMA DSP and SILENT CINEMA DSP –when the 6ch Stereo, DOLBY DIGITAL/Normal or DTS/ Normal program is selected; –when the sound effect is turned off; –when 6CH INPUT is selected as the input source; –when 96-kHzsampling digital signals are input to this unit; TUNING Automatic (or Manual) Tuning 1 Press INPUT l / h to select TUNER as the input source 2Press FM/AM to select the reception band Presetting Stations ■Automatically presetting stations (for RDS stations) 1Press FM/AM to select the FM band 3Press and hold MEMORY (MAN’L/AUTO FM) for more than 3 seconds Automatic preset tuning options ■ Manually presetting stations 5 Press MEMORY (MAN’L/AUTO FM) while the You can also store up to 40 stations (8 stations x “MEMORY” indicator is flashing groups) manually Exchanging Preset Stations 2,4 1Tune in to preset station “E1” 2Press and hold PRESET/TUNING (EDIT) for more than 3 seconds 3Tune in to preset station “A5” by using the buttons on the front panel RECEIVING RDS STATIONS PTY SEEK Function 1 Press PTY SEEK MODE to set the unit in the PTY SEEK mode ■To cancel this function ■Program types in the PTY mode EON Function 1Make sure that the “EON” indicator lights up on the front panel display The selected program type name indicator lights up on the front panel display BASIC RECORDING SET MENU SET MENU 1/4 2 LOW FRQ TEST 1A CENTER SP 1B MAIN SP 1C REAR L/R SP 1D REAR CT SP 1E LFE/BASS OUT 1F MAIN LEVEL 3 L/R BALANCE (balance of the left and right main speakers) Control range: 10 steps for L/R Initial setting: 4 HP TONE CTRL (headphone 10 DOLBY D. SET (Dolby Digital 11 DTS LFE LEVEL This setting is effective only when this unit decodes DTS signals Control range (dB): –10to +10 12 6.1/ES AUTO Choices: ON, OFF 14 DISPLAY SET ■BLUE BACK > AUTO/OFF ■OSD SHIFT (OSD off-setposition) This setting is used to adjust the vertical position of the OSD ■DIMMER ADJUSTING THE LEVEL OF THE EFFECT SPEAKERS SLEEP TIMER REMOTE CONTROL FEATURES ■SOURCE SELECT k / n ■OPTN (option) area Each Component Control Area The YAMAHA code is factory set for the A, TUNER, MD/TAPE, CD ■Operating a tuner (TUNER area) ■Operating a CD player (CD area) When the manufacturer code for your TV is set up in the both ■Operating an MD recorder (MD/TAPE area) ■Operating a CD recorder (CD-Rarea) ■Operating an LD player (A area) ■Operating a DVD player (DVD area) ■ Operating a VCR (VCR 1, VCR 2/DVR and V-AUXareas) ■Operating a TV/digital TV (D-TV/LDand PHONO areas) If you operate an LD player in the ■Operating a cable TV (CBL/SAT area) or satellite tuner (B area) ■Free area (OPTN area) Setting the Manufacturer Code 3Press k / n to select the name of your component’s manufacturer If the component cannot be controlled with the remote / control, try setting another code for the same manufacturer Programming a New Remote Control Function (Learn Feature) 1 Set 10KEY/DSP to 10KEY 2Press an input selector button, A or B to select a source component 4Press LEARN by using a ballpoint pen or similar object 7Repeat steps 5 and 6 to program additional functions 8Press LEARN again to exit from the learning mode 5Press the button for which you want to program the new function “LEARN” is displayed Using the Macro Feature ■Operating the macro 1Set MACRO ON/OFF to ON 2Press a macro button •When you have finished using the Macro feature, set MACRO ON/OFF to OFF ■Programming a macro Changing the Source Name in the Macros, Renamed Source Names SOUND FIELD PROGRAM CINEMA DSP Programs ■For audio-videosources: Nos. 7 to Game This program adds a deep and spatial feeling to video game sounds TV SPORTS (group) 70 mm Adventure DGTL Adventure *1 Adventure 6.1 *2 DTS Adventure *1 q/DTS Normal PRO LOGIC/Normal Analog, PCM The built-indecoder precisely reproduces sounds MOVIE THEATER Programs ■Dolby Pro Logic + DSP sound field effect ■Dolby Digital/DTS + DSP sound field effect ■Dolby Digital Matrix 6.1/DTS ES + DSP sound field effect SOUND FIELD PROGRAM PARAMETER EDITING Sound Field Program Parameters P05 ROCK CONCERT Digital Sound Field Parameter Descriptions ■INIT.DLY (initial delay) (P.INIT.DLY — for the presence sound field) Function: direct sound and the first reflection heard by the listener ■LIVENESS early reflections decay 0 – room ■S.DELAY (surround delay) ■RC.INIT.DLY (rear center initial delay) sound field ■RC.ROOM SIZE (rear center room size) ■RC.LIVENESS (rear center liveness) ■REV.TIME (reverberation time) ■REV.DELAY (reverberation delay) ■REV.LEVEL (reverberation level) ■CT.DELAY (center delay) ■LS.DELAY (left surround delay) ■RC.DELAY (rear center delay) TROUBLESHOOTING Page English APPENDIX ■Tuner ■Remote control SPECIFICATIONS Page Quick Reference Card ■Remote Control ■TUNER ■CD ■MD ■ LD (A) ■ VCR ■ DVD ■ TV (TV/LD) ■CBL/SAT (CBSAT)