Learn Feature
If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so the buttons are programmable independently for each source component area.
Note
•This remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of the other remote control’s functions. However, you may not be able to program some special signals or extremely long transmissions. (Refer to the operation instructions for the other remote control.)
■Programming a new remote control function1 Press an input selector button or A to select a source component.SYSTEM | STANDBY |
| 6CH INPUT |
POWER | SLEEP | ||
A | PHONO | TUNER | CD |
CBL/SAT | MD/TAPE | ||
VCR 1 | VCR2/DVR | DVD |
REMOTE CONTROL FEATURES
4 Press the button for which you want to program the new function.“LEARN” is displayed.
|
| SKIPDISC | REC | TV | POWER | D | AUX | A | SYSTEM POWER | TRANSMIT |
|
| TV/LD | ||||||||
|
|
|
|
|
| - | V |
|
|
|
|
|
|
|
|
|
| - |
|
|
|
|
|
|
|
|
| 1 VCR | CBL/SAT | PHONO | STANDBY | CLEAR |
|
| AUDIO |
| AV | POWER | VCR2/DVR | MD/TAPE | TUNER | SLEEP | |
– | VOL | + |
|
| SELECT | DVD | CD | INPUT 6CH | LEARN |
5 Press and hold the button on the other remote control that has the function you want to program into this remote control until “OK” appears in the display window.
TV | POWER |
| D | AUX | A | SYSTEM POWER | TRANSMIT |
| TV/LD | ||||||
|
|
| - | V |
|
|
|
|
|
|
| - |
|
|
|
|
|
| 1 VCR | CBL/SAT | PHONO | STANDBY | CLEAR |
AV | POWER |
| VCR2/DVR | MD/TAPE | TUNER | SLEEP | |
| AMP | SELECT | DVD | CD | INPUT 6CH | LEARN |
2 Place this remote control and the other remote control 1 to 4 cm apart on a flat surface so that their infrared transmitters are aimed at each other.
TV | POWER |
| D | AUX | A | SYSTEM POWER | TRANSMIT |
| TV/LD | ||||||
|
|
| - | V |
|
|
|
|
|
|
| - |
|
|
|
|
|
| 1 VCR | CBL/SAT | PHONO | STANDBY | CLEAR |
AV | POWER |
| VCR2/DVR | MD/TAPE | TUNER | SLEEP | |
| AMP | SELECT | DVD | CD | INPUT 6CH | LEARN |
1 to 4 cm (approximately 1 inch)
3 Press LEARN by using a ballpoint pen or similar object.Do not press and hold LEARN longer than three seconds. Otherwise this unit enters the manufacturer code setting mode.
LEARN
Flashes alternately
Notes
•Complete each of the following steps in 30 seconds. Otherwise, the learning mode will be automatically canceled. In this case, press LEARN again.
•Do not press and hold LEARN longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting mode.
Notes
•“NG” appears in the display window when programming has not been done correctly. In this case, start over from step 4.
•This remote control can learn approximately 120 functions. However depending on the signals learned, “FULL” may appear in the display window much earlier than this number. In this case, clear unnecessary programmed functions to make further learning on the remote control.
6 Repeat steps 4 and 5 to program additional functions.7 Press LEARN again to exit from the learning mode.LEARN
Notes
•Learning may not be possibe in the following cases:
–when the batteries in the remote control for this unit or other components are weak
–when the distance between the two remote controls is too much or too little
–when the remote control infrared windows are not facing at the appropriate angle
–when the remote control is exposed to the direct sunlight
–when the function to be programmed is continuous or uncommon
•“ERROR” appears in the display window when pressing buttons other than indicated in each step.
47
OPERATION | ADVANCED |
|
|
English