Manuals / Brands / Home Audio / Stereo System / Yamaha / Home Audio / Stereo System

Yamaha RX-V1400 Connecting the antennas, 75-ohm/300-ohmantenna adapter, (U.K. model only), ■Connecting the AM loop antenna

1 90

Download 90 pages, 3.6 Mb

100kHz/10kHz

50kHz/9kHz

FM AM

FREQUENCY

STEP

Connecting the antennas

Both AM and FM indoor antennas are included with this unit. In general, these antennas should provide sufficient signal strength. Connect each antenna correctly to the designated terminals.

AM loop antenna			Indoor FM antenna
(included)			(included)

COMPONENT VIDEO

PR PB Y

VD

TV

NITOR OUT

TUNER

AM

ANT

GNDMAI

FM ANT 75Ω

UNBAL.

SURRO

SUB

WOOF

Ground (GND terminal)

For maximum safety and minimum interference, connect the antenna GND terminal to a good earth ground. A good earth ground is a metal stake driven into moist earth.

CONNECTIONS

Notes

•The AM loop antenna should be placed away from this unit.

•The AM loop antenna should always be connected, even if an outdoor AM antenna is connected to this unit.

•A property installed outdoor antenna provides clearer reception than an indoor one. If you experience poor reception quality, an outdoor antenna may improve the quality. Consult the nearest authorized YAMAHA dealer or service center about outdoor antennas.

■	75-ohm/300-ohm antenna adapter	PREPARATION
■	75-ohm/300-ohm antenna adapter
	(U.K. model only)
1	Open the cover of the
	included 75-ohm/300-ohm
	antenna adapter.

2Cut the external sleeve

	of the 75-ohm coaxial	11 (7/16)	Unit:
	of the 75-ohm coaxial	8 (5/16)	Unit:
		8 (5/16)	mm (inch)
	cable and prepare it for 6 (1/14)		mm (inch)
	connection.
	3 Cut the lead wire and		Lead wire
	remove it.

■Connecting the AM loop antenna

1Set up the AM loop antenna, then connect it to the terminals on this unit.

4 Insert the cable
wire into the slot,	Clamp	Clamp
and clamp it with
pliers.	Insert the wire
	Insert the wire
	into slot.

5Snap the cover

into place.

2Press and hold the tab to insert the AM loop antenna lead wires into the AM ANT and GND terminals.

3Orient the AM loop antenna for the best reception.

■FREQUENCY STEP switch (Asia and General models only)

Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (locating on the rear panel) according to the frequency spacing in your area.

•North, Central and South America: 100 kHz/10 kHz

•Other areas: 50 kHz/9 kHz

Before setting this switch, disconnect this unit’s AC power cord from the wall outlet.

English

21

Contents

AV Receiver l CAUTION CAUTION CAUTION: READ THIS BEFORE OPERATING YOUR UNIT Ill4 CAUTION CONTENTS FEATURES Built-in 7-channelpower amplifier Sound field features Sophisticated AM/FM tuner Other features GETTING STARTED Supplied accessories Installing batteries in the remote control Notes on batteries CONTROLS AND FUNCTIONS Front panel ■U.K. and Europe models only ■Opening and closing the front panel door Remote control Using the remote control ■Handling the remote control Front panel display Page Rear panel SPEAKER SETUP Speaker placement Front speakers (FR and FL) Center speaker (C) Surround speakers (SR and SL) Speaker connections Page ■FRONT terminals ■CENTER terminals ■SURROUND terminals ■SUBWOOFER jack ■SURROUND BACK terminals CONNECTIONS Before connecting components ■Signal directions and cable indications ■Analog jacks ■Digital jacks Connecting video components ■Connections for DVD playback ■Connecting to the MULTI CH INPUT jacks ■Connections for other video components ■VIDEO AUX jacks (on the front panel) Connecting audio components ■Connections for audio components ■ Connecting a turntable ■Connecting to an external amplifier Connecting the antennas 75-ohm/300-ohmantenna adapter (U.K. model only) ■Connecting the AM loop antenna ■FREQUENCY STEP switch (Asia and General models only) ■Connecting the AC power cord (U.S.A. and Canada models) (Other models) ■AC OUTLET(S) (SWITCHED) ■VOLTAGE SELECTOR Speaker impedance setting Turning on the power AUTO SETUP Introduction WIRING DISTANCE SIZE Starting the setup If you selected AUTO in step If you selected RELOAD in step If you selected STEP in step ■Troubleshooting for auto setup procedure BASIC SETUP Using BASIC setup Page PLAYBACK Basic operations ■Selecting the MULTI CH INPUT ■Playing video sources in the background Selecting sound field programs ■Front panel operation ■Enjoying multi-channelsoftware ■Remote control operation ■Enjoying 2-channelsoftware ■Listening to high fidelity stereo sound (Direct Stereo) ■Listening at night ■Downmixing to 2 channels Selecting input modes ■Virtual CINEMA DSP Displaying the information about the input source TUNING Automatic and manual tuning ■Automatic tuning ■Manual tuning Presetting stations ■Automatically presetting FM stations Automatic preset tuning options ■Manually presetting stations Selecting preset stations Exchanging preset stations RECORDING ■Special considerations when recording DTS software SOUND FIELD PROGRAM DESCRIPTIONS For movie/video sources Page For music sources ADVANCED OPERATIONS Selecting the OSD mode Using the sleep timer ■Setting the sleep timer ■Canceling the sleep timer Manually adjusting speaker levels Using the test tone SET MENU ■Auto Setup ■Manual Setup Option menu Using SET MENU 3 Press u / d repeatedly to select a menu then press j / i to enter the menu item 2,3,4 2,3,5 Manual setup: SOUND ■Speaker set SPEAKER SET ■Speaker level SP LEVEL ■Speaker distance SP DISTANCE ■Graphic equalizer GRAPHIC EQ ■Low-frequencyeffect level LFE LEVEL ■Dynamic range DYNAMIC RANGE ■Low frequency test LOW FRQ. TEST ■Headphone tone control HP TONE CTRL ■Audio set AUDIO SET ■Presence/surround back channel select Manual setup: INPUT ■ Input/output assignment I/O ASSIGN ■Input mode INPUT MODE ■Input rename INPUT RENAME ■External input EXT.INPUT Manual setup: OPTION ■ Display set DISPLAY SET ■Memory guard MEMORY GUARD ■Parameter initialization PARAM. INI ■Speaker impedance setting SP IMP.SET ■Zone set ZONE SET ■Zone 2 set ZONE2 SET REMOTE CONTROL FEATURES Control area ■Controlling this unit ■Controlling other components Setting manufacturer codes Programming codes from other remote controls Changing source names in the display window Clearing function sets Clearing individual functions ■Clearing a learned function Controlling each component ■Operating a DVD player (DVD area) ■Operating a VCR or a DVD recorder (VCR 1, DVR/VCR2 and V-AUXareas) ■Operating a digital TV (DTV area) or a cable/satellite TV (CBL/SAT area) ■Operating an LD player ■Operating a CD player (CD area) ■Operating a CD recorder (CD-Rarea) or an MD recorder (MD/TAPE area) ■ Operating a tape deck (MD/TAPE area) ■ Operating a tuner (TUNER area) ZONE 2/ZONE (U.S.A., CANADA AND AUSTRALIA MODELS ONLY) Zone 2/Zone 3 connections ■System configuration and connections example Remote controlling Zone 2/Zone ■To control Zone 2/Zone ■To enable Zone mode on the remote control ■Turning this unit to either on or standby ■Special considerations for DTS software EDITING SOUND FIELD PARAMETERS What is a sound field Changing parameter settings ■Elements of a sound field ■Resetting parameters to the factory values SOUND FIELD PARAMETER DESCRIPTIONS ■DSP LEVEL ■INIT. DLY/P. INT. DLY (Initial delay) ■ROOM SIZE/P. ROOM SIZE (Room size) ■LIVENESS ■S. INIT. DLY (Surround initial delay) ■S. ROOM SIZE (Surround room size) ■S. LIVENESS (Surround liveness) ■SB INIT. DLY (Surround back initial delay) ■REV.TIME (Reverberation time) ■REV.DELAY (Reverberation delay) ■REV. LEVEL (Reverberation level) ■DIALG.LIFT (Dialog lift) For 7ch Stereo ■CT LEVEL (Center level) ■SL LEVEL (Surround left level) ■SR LEVEL (Surround right level) TROUBLESHOOTING ■General Page Page ■Tuner ■Remote control GLOSSARY ■Dolby Surround ■Dolby Digital ■Dolby Pro Logic ■DTS (Digital Theater Systems) ■SILENT CINEMA ■Composite Video signal ■S VIDEO signal ■Component video signal ■PCM (Linear PCM) ■Timbre Matching ■Adaptive Decorrelation ■THX Select ■THX Surround EX ■ITU-R SPECIFICATIONS