REMOTE CONTROL FEATURES

Programming a New Remote

Control Function (Learn Feature)

If you want to program functions not included in the basic operations covered by the manufacturer code, or a manufacturer code is not available, the following procedure needs to be performed. The possible programming area is the same as a component control area, so the buttons are programmable independently for each source component area.

Note

•This remote control transmits infrared rays. If the other remote control also uses infrared rays, this remote control can learn most of the other remote control’s functions. However, you may not be able to program some special signals or extremely long transmissions. (Refer to the operation instructions for the other remote control.)

1 Set 10KEY/DSP to 10KEY.

10KEY DSP

 

 

 

 

 

 

 

 

2 Press an input selector button, Å or ı to select a source component.

 

 

A

B

PHONO

V-AUX

TUNER

MD/TAPE

CD-R

CD

D-TV/LD

CBL/SAT

VCR 1

VCR2/DVR

DVD

3 Place this remote control and the other remote control about 5 to 10 cm apart on a flat surface so that their infrared transmitters are aimed at each other.

ENTER

TITLE

TV/LD-D

AUX-V

SYSTEM POWER

TRANSMIT

1VCRVCR2/DVRCBL/SAT

R-CDMD/TAPETUNER

BA

MACROLEARNCLEAR NAME-RE

 

 

 

 

STANDBY

 

 

INPUT 6CH

DVD

CD

PHONO

MACRO ON OFF

5 to 10 cm (2 to 4 inch)

4 Press LEARN by using a ballpoint pen or similar object.

Do not press and hold LEARN longer than three seconds. Otherwise this unit enters the manufacturer code setting mode.

LEARN

Flashes alternately

Note

•If you do not press any button within 30 seconds during steps 5 and 6, the learning process is canceled. If this happens, start

over from step 4.

5 Press the button for which you want to program the new function.

“LEARN” is displayed.

SOURCE

ENTER

TITLE

1VCRVCR2/DVRCBL/SAT TV/LD-D

R-CDMD/TAPETUNERAUX-V

SYSTEM POWER

MACROLEARNCLEAR NAME-RE TRANSMIT

 

BA

 

 

 

 

 

 

STANDBY

 

 

 

 

INPUT 6CH

DVD

CD

PHONO

ON OFF

MACRO

6 Press and hold the button on the other remote control that has the function you want to program into this remote control until “OK” appears in the display window.

ENTER

TITLE

TV/LD-D

AUX-V

SYSTEM POWER

TRANSMIT

1VCRVCR2/DVRCBL/SAT

R-CDMD/TAPETUNER

BA

MACROLEARNCLEAR NAME-RE

 

 

 

 

STANDBY

 

 

INPUT 6CH

DVD

CD

PHONO

MACRO ON OFF

Notes

•“NG” appears in the display window when programming has not been done correctly. In this case, start over from step 5.

•This remote control can learn approximately 120 functions. However depending on the signals learned, “FULL” may appear in the display window much earlier than this number. In this case, clear unnecessary programmed functions to make further learning on the remote control.

7 Repeat steps 5 and 6 to program additional functions.8 Press LEARN again to exit from the learning mode.

LEARN

Notes

•It is also possible to program in the control area of this unit with 10KEY/DSP set to DSP. However, if you program functions in this area, you cannot control this unit and select a DSP program.

•Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to this remote control.

•When the remote controls are either too close together or too far apart, you may not be able to program this remote control.

•Direct sunlight interferes with infrared rays.

•“ERROR” appears in the display window in the following circumstances:

–when pressing more than one button at once; or

–when MACRO ON/OFF is switched to another position.

44