Yamaha RX V2095RDS 13

KRDS MODE button

When an RDS station is received, pressing this button changes the display mode into the PS mode, PTY mode, RT mode and/or CT mode (if the station employs these RDS data services) in turn.

LEON button

Press this button to select a desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to call a radio program of that program type automatically.

MPTY SEEK MODE button

Press this button to set the unit to the PTY SEEK mode.

NPTY SEEK START button

Press this button to begin searching for a station after the desired program type is selected in the PTY SEEK mode.

OPRESET/TUNING (EDIT) button

Press this button to alternately illuminate and turn off “PRESET” on the display panel.This button switches the function of the PRESET STATIONS/TUNING button.

This button is also used to exchange the places of two preset stations with each other.

PFM/AM button

Press this button to switch the reception band between FM and AM.

QMEMORY (MAN’L/AUTO FM) button

Use this button to enter a station to memory. Refer to the section “Manual preset tuning” on page 43 for details. Hold down this button for more than 3 seconds to start automatic preset tuning. Refer to page 45 for details.

RTUNING MODE (AUTO/MAN’L MONO) button

Press this button to switch the tuning mode between automatic and manual. To select the automatic tuning mode, press this button so that the “AUTO” indicator is illuminated on the display. To select the manual tuning mode, press this button so that the “AUTO” indicator is not illuminated.

GETTING STARTED

English

11

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ BEDIENUNGSANLEITUNGII BRUKSANVISNINGI MANUALE DII ISTRUZIONII I Page CONTENTS English Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit For U.K. customers INTRODUCTION Features Power, 0.02% THD, 20–20,000Hz What’s DSP Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Getting started Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Page Page Display panel AB C PREPARATION Speaker setup mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Connections m Basic connections of video units VIDEO AUX terminals (on the front panel) For connecting with a TV monitor that uses a 21 pin connector for input mConnecting to digital (OPTICAL and COAXIAL) terminals mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna Plugging in this unit AC OUTLETS (3 SWITCHED OUTLETS) On screen display Selecting the output modes (“SET MENU” mode) 1.SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections Speaker balance adjustment Page 11 BASIC OPERATION Playing a source Page When you finish using this unit mSwitching the input mode vFor CD, TAPE/MD and TV/DBS sources: AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) Page Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to store the first station received by the automatic preset tuning to the desired preset station number; If you want to make the automatic preset tuning mExchanging preset stations Receiving RDS stations mProgram types in the PTY mode NEWS News: AFFAIRS INFO SPORT Sport: EDUCATE English Selecting your desired program type from among preset RDS stations (PTY SEEK) To cancel this function Automatic selection of desired program when broadcasting starts Using digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES “SET MENU” mode 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields mSelecting and editing program parameters P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer REMOTE CONTROLLER Basic operation (Cover is open) Page Using the “learning-capable”keys (Cover is open) Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Page Methods of learning and clearing functions mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL