Yamaha RX V2095RDS 40

BASIC OPERATION

Notes on input mode selection

●The input mode for a TV/DBS source is selected with function “7. TV/DBS INPUT” in the SET MENU mode. This unit will be automatically set to the selected input mode when the power is turned on.

●Set the input mode to the AUTO or D.D.RF mode to play a DVD/LD source encoded with Dolby Digital.

●Select the ANALOG mode to play a normal 2-channel source with a Dolby Pro Logic Surround program.

●The sound output may be interrupted in some LD and DVD players in the following situation:

The input mode is set to AUTO. A search is made while playing the disc encoded with Dolby Digital or DTS, then disc playing is restored. The sound output is interrupted for a moment because the digital input signal was selected again.

●The input mode cannot be changed for PHONO, TUNER, VCR 1, VCR 2 and VIDEO AUX sources because only analog signals are used.

●The present input mode appears on the front display and monitor screen when the input source is changed to DVD/LD, CD, TAPE/MD or TV/DBS, or the input mode is changed.

The present input signal also appears when the input mode is changed to AUTO, as shown in the following figure.

	DVD/LD	TAPE/MD
	TV/DBS	CD
	VCR 1	TUNER
	VCR 2	PHONO
SPEAKERS	V-AUX
A

*However, the present input signal will not appear when the input mode is switched during the speaker test mode. Only AUTO will be displayed.

Notes on playing a source encoded with DTS

●Select the DTS mode when playing an LD or CD source encoded with DTS. (Red “dts” indicator is illuminated on the display panel.) If the “AUTO” mode is selected, a noise may be heard just after playback begins.

Do not play these sources in the ANALOG mode because only background noise will be output from the speakers.

●This unit is automatically locked in the DTS decoding mode when playing a CD or LD source encoded with DTS in the AUTO mode to prevent background noise in future operation. The red “dts” indicator will be flashing. In the above mode, no sound will be heard if a disc with normal digital signals (PCM) is played from a CD or LD source. The INPUT MODE button on the front panel, or, the input selector key for the current source on the remote controller must be pressed so that “PCM” appears on the display panel.

38

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ BEDIENUNGSANLEITUNGII BRUKSANVISNINGI MANUALE DII ISTRUZIONII I Page CONTENTS English Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit For U.K. customers INTRODUCTION Features Power, 0.02% THD, 20–20,000Hz What’s DSP Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Getting started Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Page Page Display panel AB C PREPARATION Speaker setup mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Connections m Basic connections of video units VIDEO AUX terminals (on the front panel) For connecting with a TV monitor that uses a 21 pin connector for input mConnecting to digital (OPTICAL and COAXIAL) terminals mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna Plugging in this unit AC OUTLETS (3 SWITCHED OUTLETS) On screen display Selecting the output modes (“SET MENU” mode) 1.SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections Speaker balance adjustment Page 11 BASIC OPERATION Playing a source Page When you finish using this unit mSwitching the input mode vFor CD, TAPE/MD and TV/DBS sources: AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) Page Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to store the first station received by the automatic preset tuning to the desired preset station number; If you want to make the automatic preset tuning mExchanging preset stations Receiving RDS stations mProgram types in the PTY mode NEWS News: AFFAIRS INFO SPORT Sport: EDUCATE English Selecting your desired program type from among preset RDS stations (PTY SEEK) To cancel this function Automatic selection of desired program when broadcasting starts Using digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES “SET MENU” mode 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields mSelecting and editing program parameters P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer REMOTE CONTROLLER Basic operation (Cover is open) Page Using the “learning-capable”keys (Cover is open) Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Page Methods of learning and clearing functions mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL