Yamaha RX V2095RDS CAUTION : Read this before operating your unit, For U.K. customers, SELECTOR, IMPEDANCE, Special Instructions for U.K. Model

CAUTION : Read this before operating your unit.

1.	To assure the finest performance, please read this manual
	carefully. Keep it in a safe place for future reference.
2.	Install this unit in a cool, dry, clean place – away from
	windows, heat sources, sources of excessive vibration,
	dust, moisture and cold. Avoid sources of humming
	(transformers, motors). To prevent fire or electrical shock,
	do not expose the unit to rain or water.
3.	Never remove the unit cover. Contact your dealer if an
	object falls inside the unit.
4.	Do not use force on switches, controls or connection wires.
	When moving the unit, first disconnect the power plug and
	the wires connected to other equipment. Never pull on the
	wires themselves.
5.	The openings on the unit cover assure proper ventilation of
	the unit. If these openings are obstructed, the temperature
	inside the unit will rise rapidly. Therefore, avoid placing
	objects against these openings, and install the unit in a
	well-ventilated area to prevent fire and damage.
	<Europe and U.K. models>
	Be sure to allow a space of at least 10 cm behind, 20 cm
	on the both sides and 30 cm above the top panel of the
	unit to prevent fire and damage.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this mode, this unit is designed to consume a small amount of power.

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.

IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED;

The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit is in the standby mode.

(Europe model)

6.	The voltage used must be the same as that specified on
	this unit. Using this unit with a higher voltage than
	specified is dangerous and may result in fire or other
	accidents. YAMAHA will not be held responsible for any
	damage resulting from use of this unit with a voltage other
	than specified.
7.	Digital signals generated by this unit may interfere with
	other equipment such as tuners, receivers or TVs. Move
	this unit farther away from such equipment if interference

KERS

REAR

(SURROUND)

OR CORRECT SETTING.

AIN A

B

AC OUTLETS

SWITCHED

I00W MAX.

TOTAL

CENTER	:	4ΩMIN. / SPEAKER
FRONT	:	6ΩMIN. / SPEAKER
REAR	:	6ΩMIN. / SPEAKER
MAIN A OR B: 4ΩMIN. / SPEAKER
A	B :	8ΩMIN. / SPEAKER
CENTER	:	8ΩMIN. / SPEAKER
FRONT	:	8ΩMIN. / SPEAKER
REAR	:	8ΩMIN. / SPEAKER
MAIN A OR B:		8ΩMIN. / SPEAKER
A	B :	I6ΩMIN. / SPEAKER

is observed.

8. Always set the VOLUME control to “–∞” before starting

the audio source play. Increase the volume gradually to an

appropriate level after playback has been started.

9. Do not attempt to clean the unit with chemical solvents;

this might damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section

regarding common operating errors before concluding that

the unit is faulty.

11. When not planning to use this unit for long periods of time,

disconnect the AC power plug from the wall outlet.

12. To prevent lightning damage, disconnect the AC power

plug and antenna cable when there is an electrical storm.

13. Grounding or polarization – Precautions should be taken

so that the grounding or polarization of an appliance is not

defeated.

14. Do not connect an audio unit to the AC outlet on the rear

panel if the equipment requires more power than the outlet

is rated to provide.

IMPORTANT

Please record the serial number of your unit in the space

below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future

reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR

MOISTURE.

SET BEFORE POWER ON

IMPEDANCE SELECTOR

IMPEDANCE

SELECTOR

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

2