Yamaha RX V2095RDS How to Connect:, Speakers

Speakers

Use speakers with the specified impedance shown on the rear of this unit.

PREPARATION

English

Front effect speakers

Rear speakers

RightLeft

RightLeft

Center speaker

Subwoofer system

		SPEAKERS
CENTER	FRONT	REAR

			(SURROUND)
		CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
		A	MAIN	A	CENTER	: 4ΩMIN. / SPEAKER
		A		A	CENTER	: 4ΩMIN. / SPEAKER
					FRONT	: 6ΩMIN. / SPEAKER
COUPLER		OUTPUT			REAR	: 6ΩMIN. / SPEAKER
COUPLER		OUTPUT			MAIN A OR B: 4ΩMIN. / SPEAKER
MAIN		CENTER FRONT REAR			A	B : 8ΩMIN. / SPEAKER
MAIN		CENTER FRONT REAR
PRE	MAIN	(SURROUND)			CENTER	: 8ΩMIN. / SPEAKER
OUT	IN				FRONT	: 8ΩMIN. / SPEAKER
		B		B	REAR	: 8ΩMIN. / SPEAKER
					MAIN A OR B: 8ΩMIN. / SPEAKER
					A	B : I6ΩMIN. / SPEAKER
					SET BEFORE POWER ON
		SUB			IMPEDANCE SELECTOR
		WOOFER

Right

Left

Right

Left

Main speakers B	Main speakers A

How to Connect:

Connect the SPEAKERS terminals to your speakers with the wire of the proper gauge (keep as short as possible). If the connections are faulty, no sound will be heard from the speakers. Make sure that the polarity of the speaker wires is correct. That is the + and – markings are observed. If these wires are reversed, the sound will be unnatural and lack bass.

Caution

Do not let the bare speaker wires touch each other or any metal part of this unit. This could damage this unit or the speakers, or both.

Red: positive (+)

Black: negative (–)

2

1

3

➀Loosen the knob.

➁Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from

the speaker wires.]

➂Tighten the knob and secure the wire.

21

Contents

OWNER’S’S MANUAL MODE D’EMPLOI’ BEDIENUNGSANLEITUNGII BRUKSANVISNINGI MANUALE DII ISTRUZIONII I Page CONTENTS English Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit For U.K. customers INTRODUCTION Features Power, 0.02% THD, 20–20,000Hz What’s DSP Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Getting started Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Page Page Display panel AB C PREPARATION Speaker setup mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Connections m Basic connections of video units VIDEO AUX terminals (on the front panel) For connecting with a TV monitor that uses a 21 pin connector for input mConnecting to digital (OPTICAL and COAXIAL) terminals mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal Antennas mConnecting the AM loop antenna mConnecting the indoor FM antenna GND terminal mOptional outdoor AM antenna mOptional outdoor FM antenna Plugging in this unit AC OUTLETS (3 SWITCHED OUTLETS) On screen display Selecting the output modes (“SET MENU” mode) 1.SPEAKER SET 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections Speaker balance adjustment Page 11 BASIC OPERATION Playing a source Page When you finish using this unit mSwitching the input mode vFor CD, TAPE/MD and TV/DBS sources: AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) Page Sound control Tuning Preset tuning mManual preset tuning To store stations To recall a preset station mAutomatic preset tuning If you want to store the first station received by the automatic preset tuning to the desired preset station number; If you want to make the automatic preset tuning mExchanging preset stations Receiving RDS stations mProgram types in the PTY mode NEWS News: AFFAIRS INFO SPORT Sport: EDUCATE English Selecting your desired program type from among preset RDS stations (PTY SEEK) To cancel this function Automatic selection of desired program when broadcasting starts Using digital sound field processor (DSP) Page mTo cancel the effect sound C E N T E R L S U R F R O N T mMethod of adjustment Speakers Control range (dB) Preset value Brief overview of digital sound field programs mProgram No. 1 to 7: Hi-FiDSP programs (for audio sources) Page mProgram No. 8 to 12: CINEMA-DSPprograms (for Audio/Video sources) Page Page ADVANCED FEATURES “SET MENU” mode 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields mSelecting and editing program parameters P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer REMOTE CONTROLLER Basic operation (Cover is open) Page Using the “learning-capable”keys (Cover is open) Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Page Methods of learning and clearing functions mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions TROUBLESHOOTING Remote controller Tuner When playing back a source encoded with DTS: SPECIFICATIONS AM SECTION GENERAL