NOTE: The parking brake must be set if the operator leaves the seat with the engine running.
NOTE: The PTO switch must be in OFF position when starting the engine, when shifting into reverse and if theopera
leaves the seat.
~\ |
|
|
|
| - | "" |
| CUTTINGCONTROLSA. |
|
|
| ||||||||
|
| Parking |
|
| LIFT | LEVER |
|
|
|
|
|
| |||||||
|
|
|
|
| " |
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| Brake |
|
|
|
| Mode1704F: |
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
| The lift lever is used to raise and lower the cutting deck | ||||||||||
|
|
|
|
| Valve | ~"'" | and to engage and disengage the blades. Pulling it all | ||||||||||||
|
|
|
|
| the | way | back and locking | it disengages | the blades. | ||||||||||
|
| ~~~ | ~~ |
| ~1:/ | NOTE: |
| The lift lever must be in the disengaged | posi- | ||||||||||
|
|
|
|
|
| tion when starting the engine, when shifting into reverseand | |||||||||||||
|
|
|
|
|
| if the operator leaves the seat. See figure 12. | |||||||||||||
FIGURE | 10. |
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
| Model | 734G:The |
|
|
|
|
| ||||||
RELIEF VALVE |
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
| lift lever is located | on the right side of the lawn | |||||||||||
A hydrostatic | relief | valve | is provided |
| so the | unit can |
| It is used to raise and lower the cutting | deck (which | ||||||||||
be moved without the engine running. |
| The lever which | sets | the | cutting | height) and other | attachments. | Movethe | |||||||||||
operates | the | relief valve is located on the console. See |
| lift lever outward, | select | the desired cutting | height | ||||||||||||
figure 10. |
|
|
|
|
|
|
| and | release the | lever. | See | figure | 12. |
|
| ||||
To operate the relief valve, place the hydrostatic con- |
|
|
|
| WARNING: The blade does not shut off | ||||||||||||||
trol lever in neutral, release the parking brake, push |
|
|
|
| |||||||||||||||
|
|
|
| when the deck is raised. You must placethe | |||||||||||||||
the lever forward and to the right to lock. Be certain |
|
|
|
| |||||||||||||||
|
|
|
| PTO switch in the OFF position. |
| ||||||||||||||
to release the lever by pushing it to the left before |
|
|
|
|
| ||||||||||||||
|
|
|
|
|
|
|
|
|
|
| |||||||||
operating | the engine. |
|
|
|
|
| B. DECK | LIFT | INDICATOR |
|
|
|
| ||||||
INDICATOR LIGHTS (Model 734G Only) |
| The | deck | lift indicator | marks the | position | being | used | |||||||||||
Three indicator lights are located | in the steering wheel. | for the | lift lever. | Select the | lift lever position desired, | ||||||||||||||
If a light | illuminates | when | attempting |
| to start | the unit, | press | the | indicator lever outward, | move | it to the posi- | ||||||||
proceed | as follows. |
|
|
|
|
|
| tion | immediately | below the | lift lever and release | the in- | |||||||
the clutch pedal. |
|
| dicator lever. See figure 12. |
|
|
| |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
SETTING THE CUTTING HEIGHT | |
|
| desired cutting height. Move the deck lift indicator | |
POWER | so that the lift lever can | be returned to the same |
(Model 734G Only) | position after it is raised. |
|
The PTO switch is located on the right side of thedashboard. |
| |
See figure 11. The PTO switch must be in | 2. Move the deck wheels to the hole location so the | |
wheels are 1/4to 1/2inch | above the ground. | |
the OFF position (down) when starting the engine, when |
|
|
shifting into reverse and if the operator leaves the seat. |
|
|
To engage the PTO switch, pull knob out and lift up to ON position, then release. The knob will return to RUN position. See figure 11.
FIGURE 11. | FIGURE 12. |
8
"~C. ./