Error Message, Description and necessary action | Fujitsu 5000

Error Message	Description and necessary action

Invalid system disk	Replace the disk, and then press any key
	This message is displayed when the PC is switched
	on while a floppy disk other then a system disk is set in
	the floppy disk drive. Remove the floppy disk and
	press any key.

Non-System disk or disk error	Replace and press any key when ready
	This message is displayed when the PC is switched
	on while a floppy disk other then a system disk is set in
	the floppy disk drive. Remove the floppy disk and
	press any key.

Operating system not found	OS cannot be found. Confirm that the drive is
	correctly set at BIOS setup or the OS is installed in the
	specified drive.

An error occurred during	The LAN cable is not correctly connected. Connect
execution of the Execution	the LAN cable correctly.
Environment.

An error occurred during	The IP address required to boot the PC was not
execution of the Preboot	obtained. Set the boot server correctly, or set 'Boot
Execution Environment.	from the network server' to Disabled on the BIOS
	setup menu.

An error occurred during	The boot filename was not obtained from the boot
execution of the Preboot	server. Set the boot server correctly, or set 'Boot from
Execution Environment.	the network server' to Disabled on the BIOS setup
	menu.

An error occurred during	There is no boot server, or the boot server does not
execution of the Preboot	work correctly. Set the boot server correctly, or set
Execution Environment.	'Boot from the network server' to Disabled on the
	BIOS setup menu.

An error occurred during	The boot image file on the boot server was not
execution of the Preboot	obtained. Set the boot server correctly, or set 'Boot
Execution Environment.	from the network server' to Disabled on the BIOS
	setup menu.

An error occurred during	Booting from a network failed. Set the boot server
execution of the Preboot	correctly, or set 'Boot from the network server' to
Execution Environment.	Disabled on the BIOS setup menu.

48

Image 58

Fujitsu 5000 user manual Error Message, Description and necessary action

Contents

DESKPOWER 5000 Series User’s Manual IMPORTANT SAFETY INSTRUCTIONS Greetings Warning icons Command entriesConventions used in this manual Representing keys and use thereof Illustrations Conventions used in the text of the manualScreen display examples Custom-made options Warning and caution labels Rear of the PC main unit Inside the PC main unit Chapter 3 Installing Internal Options Manual configurationChapter 1 Installation and Connection Chapter 4 Troubleshooting Switching on ContentInstallation Switching off Installing Expansion Bay Options Installing Memory ModulesInstalling Expansion Cards Error Messages 1 Name and Function of Each Component Standard SpecificationsCleaning Method Supplement Chapter 1 Installation and Connection and explains how to connect various cables Example of installing the PC 1 InstallationInstallation location ⁄ Point Precautions to be taken by the TV or radio Precautions to be taken by the PC userPreventing electromagnetic interference with a TV or radio 2 Connection the rear of the CRT display Connect the power cord to the outlet Attaching CRT display, keyboard, mouse, and LAN cables ⁄ PointConnect the power cord to the CRT display Connect the CRT cable to the PC main unit Upon completion of all connections Connecting the power cordDo not plug or unplug the power cord with wet hands Chapter 2 Basic Operations power on and off and handle storage media Press the power switch of the CRT display 1 Switching onPress the power switch of the PC main unit Wait about 10 seconds before switching the PC on or off again Turning off the power via Windows 2 Switching off1 Click Start Turning off the power via Windows NT 2 Click Shut Down Resetting the PC via Windows NT 3 ResetResetting the PC via Windows 1 Click Start and Shut Down Click Start and Shut Down Select Restart and click OK Mounting and dismounting a floppy disk Handling precautions4 Floppy Disk Mounting a floppy disk Dismounting a floppy disk 1 Confirm that the floppy disk access indicator lamp is off2 Press the floppy disk eject button 5 CD-ROM Dismounting a CD-ROM Mounting and dismounting a CD-ROM diskMounting a CD-ROM 1 Press the EJECT button. The CD-ROM tray is ejected What is a hard disk? 6 Hard Disk Chapter 3 Installing Internal Options 1 Introduction Installing positions of internal options 1 Remove three screws at the rear of the PC main unit Removing the upper coverRemoving the front panel 2 Remove the upper cover 2 Installing Memory Modules DIMM DIMM 1 Remove the upper cover Installing an additional memoryMemory 2 Push down the hooks at both ends of the slot Removing the memory 3 Attach the upper cover 3 Installing Expansion Cards Expansion cards for PCI bus Plug & Play compatible cards Expansion card installation procedure for a PC using Windows Turning on the PC after installing the Expansion card installation procedure for a PC using Windows NT Select the Exit command and press the Enter key Starting and terminating the ICU For a PC using Windows NTSet up the resources 1 If the PC is turned on, turn it off Insert the expansion card into the connector Installing an expansion cardSlide the motherboard for installing a small expansion card Remove the slot cover 8 Install the retaining metal bracket at the side Install the motherboard when a largeexpansion card has been installed for installing a large expansion card 4 Installing Expansion Bay Options genuine internal options in the PC expansion bay If retaining metal brackets are mounted on Set up the jumper switchReplacing a internal hard disk equipped as standard both sides of the internal hard disk to be replaced, remove them 6 Replace the internal hard disk 7 Install the internal hard disk in the PC main unit9 Attach the upper cover 10 Use BIOS setup to set the hard disk 8 Connect the cables to the hard disk Set the internal option Installing internal options to 3.5-inch expansion baysboth sides of the internal hard disk to be installed, remove them Remove the upper cover Remove the front panel 8 Install the internal option in the PC main unit 7 Install a internal option in the retaining metal bracket6 Remove the retaining metal bracket from the PC main unit 10 Connect the power cord 9 Connect the flat cable 11 Attach the front panel 13 Use BIOS setup to configure the internal option12 Attach the upper cover 1 Configure the internal option Installing internal options to 5-inch expansion bays5 Insert the internal option from the front side of the PC main unit Secure the internal option with two screws Connect the flat cable 10 Attach the front panel 8 Connect the power corddismounted Hook Use BIOS setup to configure the internal option Attach the upper cover Chapter 4 Troubleshooting as expected Error Message 1 Error MessagesError messages displayed by the PC Description and necessary action To boot booting the OS, press the F1 key. To run the BIOS Error Message Correcting errors No data is displayed on the screen 2 TroubleshootingThe access lamp does not light up The screen flickers Characters entered using the keyboard are not displayed Troubleshooting information on WindowsThe power is not turned on or the Power lamp on the front panel does not light up If an error recurs The mouse is disabled and Windows 98 cannot end This appendix explains how to clean the PC and provides PC main unit Appendixspecifications 1 Name and Function of Each Component Front of the PC main unit Microphone terminal Ventilation holes Rear of the PC main unitPower-switching switch Outlet Inlet MONITOR Connect the CRT cable Riser board Inside the PC main unitPower supply unit 3.5-inch expansion bay Internal hard disk Internal battery Motherboard/riser boardCPU JP3 jumper switch Primary IDE connector DESKPOWER 2 Standard SpecificationsPC main unit specifications Product name Number of Storage LAN controller LAN adapter specificationsSound specifications Intel LAN connector 100BASE-TX/10BASE-T Connector specificationsCRT connector Signal name Parallel connector Serial connector Keyboard connector Mouse connectorUSB connector SeriesA Cleaning the keyboard 3 Cleaning MethodCleaning the PC main unit Cleaning a CD-ROM Clean the inside of the mouse Cleaning a floppy disk driveRemove the ball and clean with water For Windows 9X/NT model Display disturbed when the screen mode is changed Note on using the displayNote on using an analog liquid crystal display 4 Supplement About USB Windows 98/2000 printer, modem, and speaker interfaces LAN Cable Power Saving FunctionWake up On LAN LAN Adapter Intel processor serial number CD-ROM driveMouse with scroll functionwheel 8th Floor Wisma Damansara Jalan Semantan 50490 Kuala Lumpur Malaysia Tel 65-776 Fax 65-776Tel 603-253 Fax 603-253