APPENDIX A | SYSTEM ERROR MESSAGES |
| This section details some of the front panel error messages that may ap- | |||
MESSAGES | pear. In most cases, the error condition can be easily corrected. If not, | |||
| note the error message and contact the nearest Anritsu Service Center | |||
| (see Chapter 2, Table | |||
| contain a numeric error code. |
|
| |
|
| Error Message |
| Meaning |
|
|
| ||
|
|
|
|
|
|
| SAVE RECALL STORE 0 |
| Attempting save to or recall from current |
|
|
|
| store, i.e., 0. |
|
| RECALL EMPTY STORE |
| Attempted to recall empty store. |
|
| SAVE RECALL STORE NUMBER |
| Illegal store number. |
|
|
|
| NOTE: Save Recall error messages will only |
|
|
|
| be seen under the following two conditions: |
|
|
|
| 1. While doing a save or recall over the |
|
|
|
| GPIB with the measurement display active |
|
|
|
| on the front panel. |
|
|
|
| 2. While doing a save or recall from the front |
|
|
|
| panel and quickly exiting to a measurement |
|
|
|
| display when an error is reported. |
|
|
|
|
|
|
| SENSOR A over range |
| Range Hold is selected for Sensor A, but the |
|
| SENSOR A under range |
| measured value is too large or small for the |
|
|
| range selected. | |
|
|
|
| |
|
|
|
|
|
|
| SENSOR B over range |
| Range Hold is selected for Sensor B, but the |
|
| SENSOR B under range |
| measured value is too large or small for the |
|
|
| range selected. | |
|
|
|
| |
|
|
|
|
|
|
| CHAN 1 display range |
| Channel 1 display value is greater than |
|
|
|
| +99.999 dBm or less than |
|
|
|
|
|
|
| CHAN 2 display range |
| Channel 2 display value is greater than |
|
|
|
| +99.999 dBm or less than |
|
|
|
|
|
|
| CHAN I illegal LOG calc |
| Combination of sensor values results in an |
|
|
|
| illegal calculation. |
|
|
|
|
|
|
| CHAN 2 illegal LOG calc |
| Combination of sensor values results in an |
|
|
|
| illegal calculation. |
|
|
|
|
|
|
| SENSOR A CAL error (xxxx) |
| Sensor A Cal 0 failed, xxxx = error code |
|
| SENSOR A CAL 0 dBm invalid |
| Sensor A Cal 0 dBm failed. |
|
|
|
|
|
|
| SENSOR B CAL error (xxxx) |
| Sensor B Cal 0 failed, xxxx = error code |
|
| SENSOR B CAL 0 dBm invalid |
| Sensor B Cal 0 dBm failed. |
|
|
|
|
|
|
| SENSOR A NOT ZEROED |
| as per message |
|
| SENSOR A ZERO . . . |
| ZERO in progress |
|
| SENSOR A ZERO error (xxxx) |
| ZERO failed xxxx = 4 digit code |
|
|
|
|
|
|
| SENSOR B NOT ZEROED |
| as per message |
|
| SENSOR B ZERO . . . |
| ZERO in progress |
|
| SENSOR B ZERO error (xxxx) |
| ZERO failed xxxx = 4 digit code |
|
|
|
|
|
ML2430A OM | |
|
|
