ZyXEL Communications G-120 3.3.3Notes on OTIST

ZyXEL G-120 User’s Guide

•In the wireless client, you see this screen if it can't find an OTIST-enabled AP (with the same Setup key). Click OK to go back to the ZyXEL utility main screen.

•If there is more than one OTIST-enabled AP within range, you see a screen asking you to select one AP to get settings from.

3.3.3Notes on OTIST

1If you enabled OTIST in the wireless client, you see this screen each time you start the utility. Click Yes for it to search for an OTIST-enabled AP.

2If an OTIST-enabled wireless client loses its wireless connection for more than ten seconds, it will search for an OTIST-enabled AP for up to one minute. (If you manually have the wireless client search for an OTIST-enabled AP, there is no timeout; click Cancel in the OTIST progress screen to stop the search.)

3When the wireless client finds an OTIST-enabled AP, you must still click Start in the AP OTIST web configurator screen or hold in the Reset button (for one or two seconds) for the AP to transfer settings.

4If you change the SSID or the keys on the AP after using OTIST, you need to run OTIST again or enter them manually in the wireless client(s).

5If you configure OTIST to generate a WPA-PSK key, this key changes each time you run OTIST. Therefore, if a new wireless client joins your wireless network, you need to run OTIST on the AP and ALL the wireless clients again.

Chapter 3 Wireless LAN Network

41

Contents

User’s Guide Page Copyright Disclaimer Trademarks Certifications Federal Communications Commission (FCC) Interference Statement FCC Radiation Exposure Statement Notices Viewing Certifications Safety Warnings ZyXEL Limited Warranty Note Online Registration Customer Support Page Page Table of Contents Wireless Station Mode Configuration Appendix A Appendix B Appendix C Appendix D Appendix E Page List of Figures Page List of Tables Page Preface About This User's Guide Related Documentation User Guide Feedback Syntax Conventions Graphics Icons Key Getting Started 1.1 About Your G-120 1.2 Application Overview 1.2.1.2 Ad-Hoc 1.2.2 Access Point Mode Note: 1.2.3 Changing G-120Mode Station Mode AP Mode 1.3 ZyXEL Utility Icon 1.4 Configuration Methods (All) Programs ZyXEL G-120 1.4.2 Accessing the ZyXEL Utility Page Tutorial 2.1Connecting to a Wireless LAN Scan Available Network List SSID_Examples3 Back Exit 2.2Creating and Using a Profile Profile Add Add New Profile Scan Info Select Activate Now Activate Later Profile List 2.3 Configuring the G-120as an AP Configuration Page Wireless LAN Network 3.1 Wireless LAN Overview 3.2Wireless LAN Security 3.2.3.1 WEP 3.2.3.2 IEEE 3.2.3.3 WPA and WPA2 3.3 Introduction to OTIST 3.3.1.1 AP 3.3.1.2 Wireless Client 3.3.3Notes on OTIST Page Wireless Station Mode Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Access Point Mode Page Page Page Page Page Maintenance 6.1 The About Screen 6.2 Uninstalling the ZyXEL Utility 6.3 Upgrading the ZyXEL Utility Page Page Troubleshooting 7.1 Problems Starting the ZyXEL Utility 7.2 Problems with the Link Quality 7.3 Problems Communicating With Other Computers Product Specifications Page Access Point Mode Setup Example Configuring the Computer on Which You Install the G-120 Sharing Enable Internet Connection Sharing for this connection Configuring the Wireless Station Computer Page Activating Wireless Zero Configuration Connecting to a Wireless Network Wireless Networks Wireless Network Connection Properties Refresh network list Refresh Available networks Configure Preferred Wireless Network Connection Security Settings Page Authentication Authentication Properties Smart Card or other Certificate Properties Ordering the Preferred Networks Move up Move down Remove Page Wireless Security Types of EAP Authentication Dynamic WEP Key Exchange WPA and WPA2 User Authentication WPA(2)-PSKApplication Example WPA(2) with RADIUS Application Example Security Parameters Summary Setting up Your Computer’s IP Address Windows 98/Me Installing Components Protocol Microsoft manufacturers TCP/IP Configuring IP Address Obtain an IP address automatically Specify an IP address Subnet Mask Windows 2000/XP Network Connections Network and Dial-up Connections 3Right-click Local Area Connection and then click Properties Internet Protocol (TCP/IP) General Use the following IP Address IP address Subnet mask Default gateway Advanced Use the following DNS server addresses Preferred DNS server Alternate DNS server 8Click OK to close the Internet Protocol (TCP/IP) Properties window 9Click OK to close the Local Area Connection Properties window Index