ZyXEL Communications G-120 4.2.1 Trend Chart, Link Info, Trend Chart

		ZyXEL G-120 User’s Guide
	Table 3 Station Mode: Link Info (continued)

	LABEL	DESCRIPTION

	Total Transmit	This field displays the total number of data frames transmitted.

	Total Receive	This field displays the total number of data frames received.

	Link Quality	This field displays the signal strength of the G-120.

	Trend Chart	Click this button to display the real-time statistics of the data rate in kilobits per
		second (Kbps).
	Signal Strength	The status bar shows the strength of the signal. The signal strength is mainly
		depending on the antenna output power and the distance between your G-120 and
		the AP or peer computer.
	Link Quality	The status bar shows the quality of wireless connection. This refers to the
		percentage of packets transmitted successfully. If there are too many wireless
		stations in a wireless network, collisions may occur which could result in a loss of
		messages even though you have high signal strength.

4.2.1 Trend Chart

Click Trend Chart in the Link Info screen to display a screen as shown below. Use this screen to view real-time data traffic statistics.

Figure 23 Station Mode: Link Info: Trend Chart

The following table describes the labels in this screen.

Table 4 Station Mode: Link Info: Trend Chart

LABEL	DESCRIPTION

Transmit	This field displays the current data transmission rate in kilobits per second (Kbps).

Receive	This field displays the current data receiving rate in kilobits per second (Kbps).

Chapter 4 Wireless Station Mode Configuration

45

Contents

User’s Guide Page Copyright Disclaimer Trademarks Certifications Federal Communications Commission (FCC) Interference Statement FCC Radiation Exposure Statement Notices Viewing Certifications Safety Warnings ZyXEL Limited Warranty Note Online Registration Customer Support Page Page Table of Contents Wireless Station Mode Configuration Appendix A Appendix B Appendix C Appendix D Appendix E Page List of Figures Page List of Tables Page Preface About This User's Guide Related Documentation User Guide Feedback Syntax Conventions Graphics Icons Key Getting Started 1.1 About Your G-120 1.2 Application Overview 1.2.1.2 Ad-Hoc 1.2.2 Access Point Mode Note: 1.2.3 Changing G-120Mode Station Mode AP Mode 1.3 ZyXEL Utility Icon 1.4 Configuration Methods (All) Programs ZyXEL G-120 1.4.2 Accessing the ZyXEL Utility Page Tutorial 2.1Connecting to a Wireless LAN Scan Available Network List SSID_Examples3 Back Exit 2.2Creating and Using a Profile Profile Add Add New Profile Scan Info Select Activate Now Activate Later Profile List 2.3 Configuring the G-120as an AP Configuration Page Wireless LAN Network 3.1 Wireless LAN Overview 3.2Wireless LAN Security 3.2.3.1 WEP 3.2.3.2 IEEE 3.2.3.3 WPA and WPA2 3.3 Introduction to OTIST 3.3.1.1 AP 3.3.1.2 Wireless Client 3.3.3Notes on OTIST Page Wireless Station Mode Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Access Point Mode Page Page Page Page Page Maintenance 6.1 The About Screen 6.2 Uninstalling the ZyXEL Utility 6.3 Upgrading the ZyXEL Utility Page Page Troubleshooting 7.1 Problems Starting the ZyXEL Utility 7.2 Problems with the Link Quality 7.3 Problems Communicating With Other Computers Product Specifications Page Access Point Mode Setup Example Configuring the Computer on Which You Install the G-120 Sharing Enable Internet Connection Sharing for this connection Configuring the Wireless Station Computer Page Activating Wireless Zero Configuration Connecting to a Wireless Network Wireless Networks Wireless Network Connection Properties Refresh network list Refresh Available networks Configure Preferred Wireless Network Connection Security Settings Page Authentication Authentication Properties Smart Card or other Certificate Properties Ordering the Preferred Networks Move up Move down Remove Page Wireless Security Types of EAP Authentication Dynamic WEP Key Exchange WPA and WPA2 User Authentication WPA(2)-PSKApplication Example WPA(2) with RADIUS Application Example Security Parameters Summary Setting up Your Computer’s IP Address Windows 98/Me Installing Components Protocol Microsoft manufacturers TCP/IP Configuring IP Address Obtain an IP address automatically Specify an IP address Subnet Mask Windows 2000/XP Network Connections Network and Dial-up Connections 3Right-click Local Area Connection and then click Properties Internet Protocol (TCP/IP) General Use the following IP Address IP address Subnet mask Default gateway Advanced Use the following DNS server addresses Preferred DNS server Alternate DNS server 8Click OK to close the Internet Protocol (TCP/IP) Properties window 9Click OK to close the Local Area Connection Properties window Index