ZyXEL Communications G-120 4.4 The Profile Screen

ZyXEL G-120 User’s Guide

Figure 29 Station Mode: Confirm New Settings

The following table describes the labels in this screen.

Table 10 Station Mode: Confirm New Settings

LABEL	DESCRIPTION

Network (SSID)	This field displays the SSID previously entered.
Network Type	This field displays the network type (Infrastructure or Ad-Hoc) of the wireless
	device.
Security	This field shows whether data encryption is activated (WEP, WPA-PSK, WPA,
	WPA2, WPA2-PSK,802.1x) or inactive (Disabled).
Back	Click Back to return to the previous screen.

Save	Click Save to save the changes back to the G-120 and display the Link Info
	screen.
Exit	Click Exit to discard changes and return to the Site Survey screen.

4.4 The Profile Screen

A profile is a set of wireless parameters that you need to connect to a wireless network. With a profile activated, each time you start the G-120, it automatically scans for the specific SSID and joins that network with the pre-defined wireless security settings. If the specified network is not available, the G-120 cannot connect to a network.

If you do not configure and activate a profile, each time you start the G-120, the G-120 uses the default profile to connect to any available network with security disabled.

The default profile is a profile that allows you to connect to any SSID without security.

Click the Profile tab in the ZyXEL utility program to display the Profile screen as shown next.

The profile function allows you to save the wireless network settings in this screen, or use one of the pre-configured network profiles.

52	Chapter 4 Wireless Station Mode Configuration

Contents

User’s Guide Page Copyright Disclaimer Trademarks Certifications Federal Communications Commission (FCC) Interference Statement FCC Radiation Exposure Statement Notices Viewing Certifications Safety Warnings ZyXEL Limited Warranty Note Online Registration Customer Support Page Page Table of Contents Wireless Station Mode Configuration Appendix A Appendix B Appendix C Appendix D Appendix E Page List of Figures Page List of Tables Page Preface About This User's Guide Related Documentation User Guide Feedback Syntax Conventions Graphics Icons Key Getting Started 1.1 About Your G-120 1.2 Application Overview 1.2.1.2 Ad-Hoc 1.2.2 Access Point Mode Note: 1.2.3 Changing G-120Mode Station Mode AP Mode 1.3 ZyXEL Utility Icon 1.4 Configuration Methods (All) Programs ZyXEL G-120 1.4.2 Accessing the ZyXEL Utility Page Tutorial 2.1Connecting to a Wireless LAN Scan Available Network List SSID_Examples3 Back Exit 2.2Creating and Using a Profile Profile Add Add New Profile Scan Info Select Activate Now Activate Later Profile List 2.3 Configuring the G-120as an AP Configuration Page Wireless LAN Network 3.1 Wireless LAN Overview 3.2Wireless LAN Security 3.2.3.1 WEP 3.2.3.2 IEEE 3.2.3.3 WPA and WPA2 3.3 Introduction to OTIST 3.3.1.1 AP 3.3.1.2 Wireless Client 3.3.3Notes on OTIST Page Wireless Station Mode Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Access Point Mode Page Page Page Page Page Maintenance 6.1 The About Screen 6.2 Uninstalling the ZyXEL Utility 6.3 Upgrading the ZyXEL Utility Page Page Troubleshooting 7.1 Problems Starting the ZyXEL Utility 7.2 Problems with the Link Quality 7.3 Problems Communicating With Other Computers Product Specifications Page Access Point Mode Setup Example Configuring the Computer on Which You Install the G-120 Sharing Enable Internet Connection Sharing for this connection Configuring the Wireless Station Computer Page Activating Wireless Zero Configuration Connecting to a Wireless Network Wireless Networks Wireless Network Connection Properties Refresh network list Refresh Available networks Configure Preferred Wireless Network Connection Security Settings Page Authentication Authentication Properties Smart Card or other Certificate Properties Ordering the Preferred Networks Move up Move down Remove Page Wireless Security Types of EAP Authentication Dynamic WEP Key Exchange WPA and WPA2 User Authentication WPA(2)-PSKApplication Example WPA(2) with RADIUS Application Example Security Parameters Summary Setting up Your Computer’s IP Address Windows 98/Me Installing Components Protocol Microsoft manufacturers TCP/IP Configuring IP Address Obtain an IP address automatically Specify an IP address Subnet Mask Windows 2000/XP Network Connections Network and Dial-up Connections 3Right-click Local Area Connection and then click Properties Internet Protocol (TCP/IP) General Use the following IP Address IP address Subnet mask Default gateway Advanced Use the following DNS server addresses Preferred DNS server Alternate DNS server 8Click OK to close the Internet Protocol (TCP/IP) Properties window 9Click OK to close the Local Area Connection Properties window Index