ZyXEL Communications G-220F 3.4 The Profile Screen, Profile, Profile

ZyXEL G-220F User’s Guide

3.4 The Profile Screen

Click the Profile tab in the ZyXEL Utility program to display the Profile screen as shown next.

The profile function allows you to save the wireless network settings in this screen, or use one of the pre-configured network profiles.

Figure 21 Station Mode: Profile

The following table describes the labels in this screen.

Table 11 Station Mode: Profile

	LABEL	DESCRIPTION

	Profile List	Click a column heading to sort the entries.

	,	denotes that the wireless device is in infrastructure mode and the wireless
	,	security is activated.
	,	denotes that the wireless device is in infrastructure mode but the wireless

	or	security is deactivated.
	or	denotes that the wireless device is in Ad-Hoc mode and the wireless

		security is activated.
		denotes that the wireless device is in Ad-Hoc mode but the wireless
		security is deactivated.
	Profile Name	This is the name of the pre-configured profile.

	SSID	This is the SSID of the wireless network to which the selected profile associate.

	Connect	To use a previously saved network profile, select a pre-configured profile name in
		the table and click Connect.
	Add	To add a new profile into the table, click Add.

	Delete	To delete an existing wireless network configuration, select a profile in the table
		and click Delete.

43	Chapter 3 Wireless Station Mode Configuration

Contents

User’s Guide Copyright Disclaimer Trademarks Federal Communications Commission (FCC) Interference Statement Notice Caution Certifications ZyXEL Limited Warranty Note Online Registration Customer Support Page Table of Contents Wireless Station Mode Configuration Maintenance Appendix A Appendix B Appendix C Appendix D Appendix E Page List of Figures Page List of Tables Page Preface About This User's Guide Related Documentation User Guide Feedback Syntax Conventions Graphics Icons Key Getting Started 1.1 About Your ZyXEL G-220F 1.1.1.1 Infrastructure 1.1.1.2 Ad-Hoc 1.1.1.3 Access Point Mode 1.2 ZyXEL G-220FHardware and Utility Installation 1.3 Configuration Methods 1.4 Windows XP Users Only 1.5 Accessing the ZyXEL Utility 1.6 Connecting to a Wireless LAN Security Settings 1.7 ZyXEL G-220FModes 1.8 ZyXEL Utility Screen Summary Page Wireless LAN Network 2.1 Wireless LAN Overview 2.2 Wireless LAN Security Overview 2.2.2.1 EAP Authentication 2.2.3.1 User Authentication 2.2.3.2 Encryption 2.2.4 WPA(2)-PSKApplication Example 2.2.5 WPA with RADIUS Application Example 2.3 Authentication Type 2.4Preamble Type 2.5 Introduction to OTIST 2.5.1.1 AP 2.5.1.2 Wireless Client 2.5.3Notes on OTIST Wireless Station Mode Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Access Point Mode Page Page Page Page Page Maintenance 5.1 The About Screen 5.2 Uninstalling the ZyXEL Utility 5.3 Upgrading the ZyXEL Utility Page Page Troubleshooting 6.1 Problems Starting the ZyXEL Utility Program 6.2 Problem Connecting to an Access Point 6.3 Problem with the Link Status 6.4 Problems Communicating With Other Computers Appendix A Product Specifications Page Appendix B Access Point Mode Setup Example Configuring the Computer on Which You Install the ZyXEL G- 220F Sharing Enable Internet Connection Sharing for this connection Configuring the Wireless Station Computer Page Via the Wireless Network System Tray Icon Wireless Network Connection Change advanced settings Related Tasks Wireless Networks Page Via the Control Panel Page Page Activating Wireless Zero Configuration Connecting to a Wireless Network Wireless Networks Wireless Network Connection Properties Refresh network list Refresh Available networks Configure Preferred Connect Security Settings Association Authentication Authentication Properties Smart Card or other Certificate Properties Ordering the Preferred Networks Wireless Networks Move up Move down Page Appendix E Types of EAP Authentication PEAP (Protected EAP) LEAP Dynamic WEP Key Exchange WPA Security Parameters Summary Appendix F Setting up Your Computer’s IP Address Windows 95/98/Me Installing Components Protocol Microsoft manufacturers TCP/IP Configuring IP Address Obtain an IP address automatically Specify an IP address Subnet Mask Windows 2000/NT/XP Network and Dial-up Connections 3Right-click Local Area Connection and then click Properties Internet Protocol (TCP/IP) General Use the following IP Address IP address Subnet mask Default gateway Advanced Macintosh OS 8/9 2Select Ethernet built-in from the Connect via list Using DHCP Server Configure: Macintosh OS Apply Now Page Index