![](/images/new-backgrounds/1168936/1689361x1.webp)
ZyXEL G-260
802.11g Wireless USB 2.0 Adapter
Quick Start Guide
Version 1.00
8/2005
English
Important Information
Federal Communications Commission (FCC) Interference Statement
The 802.11g Wireless LAN Adapter has been tested to the FCC exposure requirements (Specific Absorption Rate).
The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d) (2).
This Transmitter must not be
Refer to the User's Guide for general FCC statements.
Procedure to View a Product's Certification(s)
1Go to www.zyxel.com
2Select your product from the
3Select the certification you wish to view from this page.
About Your ZyXEL G-260
The ZyXEL
Installation Requirements
Before installation, make sure you have a computer with the following:
•Pentium II 300MHz or above
•A minimum of 6 MB available hard disk space
•A minimum of 32 MB RAM
•A
•A USB port (with USB1.0/1.1, the ZyXEL
•Windows 98 Second Edition (SE), Windows ME, Win- dows 2000 or Windows XP
•Windows 98 SE users may need the Windows 98 SE CD
If you install the Funk Odyssey Client software on the computer, uninstall (remove) it.
Windows XP Users
Wireless Zero Configuration (WZC) is a wireless configuration utility bundled with Windows XP. If you are a Windows XP user and want to use WZC, then you can either:
•Install the ZyXEL Utility and then disable it (by clicking the close button in any ZyXEL Utility screen)
or
•Install the driver only. In this case, you must connect the ZyXEL
ZyXEL Utility and Hardware Installation
The installation procedures are similar for all supported Windows versions.
Install the ZyXEL Utility before you insert the ZyXEL G- 260.
1Insert the support CD into the
2Select your language and click OK.
3Click Install Utility to start installation.
4A Welcome screen displays. Click Next.
5Click Next to accept the default file location or click Browse to select an alternate folder.
6Click Finish to restart the computer.
7Locate an available CardBus slot on the computer.
8Remove the protective cap to expose the USB connector. Insert the ZyXEL
if the ZyXEL
Never bend, force or twist the ZyXEL
After you install the ZyXEL Utility and insert the ZyXEL
Driver Installtion for Windows XP
1Remove the protective cap to expose the USB connector. Insert the ZyXEL
2The Found New Hardware Wizard window appears. Select Install from a list of specific location (Advanced) and click Next.
3Insert the included CD into your
4A warning screen displays. Click Continue Anyway.
5After the driver has been installed successfully, click Finish to complete the installation.
Refer to the User's Guide to configure the ZyXEL
Introduction to OTIST
In a wireless network, the wireless clients must have the same SSID and security settings as the access point (AP) or wireless router (we will refer to both as "AP" here) in order to associate with it. Traditionally this meant that you had to configure the settings on the AP and then manually configure the exact same settings on each wireless client.
OTIST
Enabling OTIST
You must enable OTIST on both the AP and wireless client before you start transferring settings.
We use the Prestige 334WT and the
The AP and wireless client(s) MUST use the same Setup key.
AP
You can enable OTIST using the Reset button or the web configurator. If you use the Reset button, the default (01234567) or previous saved (through the web configurator) Setup key is used to encrypt the settings that you want to transfer.
Hold in the Reset button for one or two seconds.
If you hold in the Reset button too long, the device will reset to the factory defaults!
In the web configurator, go to the Wireless LAN main screen and then select OTIST. To change the Setup key, enter zero to eight printable characters. To have OTIST automatically generate a
Wireless Client
Start the ZyXEL Utility and click the Adapter tab. Select the OTIST check box, enter the same Setup Key as your AP's and click Save.
Starting OTIST
You must click Start in the AP OTIST web configurator screen and in the wireless client(s) Adapter screen all within three minutes (at the time of writing). You can start OTIST in the wireless clients and AP in any order but they must all be within range and have OTIST enabled.
1In the AP, a web configurator screen pops up showing you the security settings to transfer. After reviewing the settings, click OK.
2This screen appears while OTIST settings are being transferred. It closes when the transfer is complete.
•In the wireless client, you see this screen if it can't find an
•If there is more than one
Notes on OTIST
1If you enabled OTIST in the wireless client, you see this screen each time you start the ZyXEL Utility. Click Yes for it to search for an
2If an
3When the wireless client finds an
4If you change the SSID or the keys on the AP after using OTIST, you need to run OTIST again or enter them manually in the wireless client(s).
5If you configure OTIST to generate a
Troubleshooting
If Windows does not
•Make sure the ZyXEL
•Perform a hardware scan by clicking Start, Settings, Control Panel and
•Check for possible hardware conflicts. In Windows, click Start, Settings, Control Panel, System, Hard- ware and then click Device Manager. Verify the sta- tus of the ZyXEL
•Install the ZyXEL
Deutsch
Vorgehensweise zum Aufrufen einer Produktzertifizierung
1Gehe Sie zu www.zyxel.com
2Wählen Sie Ihr Produkt aus der Auswahlliste auf der ZyXEL Homepage aus, um die Seite des entsprechenden Produkts aufzurufen.
3Wählen Sie die Zertifizierung aus, die Sie von dieser Seite aus aufrufen möchten.
Über Ihr ZyXEL G-260
Der ZyXEL
Installationsanforderungen
Stellen Sie bitte vor der Installation sicher, dass Ihr Computer die folgenden Anforderungen erfüllt:
•Pentium II 300MHz oder höher
•Mindestens 6 MB freier Festplattenspeicher
•Mindestens 32 MB RAM
•
•Ein
•Windows 98 Second Edition, Windows ME, Windows 2000 oder Windows XP
•Benutzer von Windows 98 SE benötigen unter Umständen die Windows 98 SE CD
Wenn Sie Funk Odyssey
Wenn Sie mit Windows XP arbeiten
WZC (Wireless Zero Configuration) ist ein Utility- Programm für die Drahtloskonfiguration, das bei Windows XP enthalten ist. Wenn Sie mit Windows XP arbeiten und WZC verwenden möchten, können Sie entweder
•das ZyXEL
oder
•nur den Treiber installieren. In diesem Fall muss zue- rst der ZyXEL
ZyXEL Utility- und Hardware-Installation
Der Installationsvorgang ist für alle unterstützten
Bitte installieren Sie das "ZyXEL Utility" bevor Sie den
1Legen Sie die CD in das
2Wählen Sie Ihre Sprache und klicken dann auf OK.
3Klicken Sie auf Installationshilfsprogramm, um die Installation zu starten.
4Ein Begrüßungsbildschirm wird angezeigt. Klicken Sie auf Weiter.
5Klicken Sie auf Weiter, um den vorgegebenen Zielordner zu bestätigen oder klicken Sie auf Durchsuchen, um einen anderen Ordner auszuwählen.
6Klicken Sie auf Fertigstellen, um den Computer neu zu starten
7Entfernen Sie die Schutzkappe vom USB- Stecker. Stecken Sie den ZyXEL
Wenn der ZyXEL
Versuchen Sie unter keinen Umständen, die ZyXEL G- 260 durch Biegen, Drehen oder Gewaltanwendung in den Einschub zu schieben.
Nach Installation des ZyXEL Utility und Einschieben der ZyXEL
Wenn das ZyXEL Utility Symbol angezeigt wird, ist die ZyXEL
Treiberinstallation unter Windows XP
Wenn Sie den Windows XP Wireless Zero Configuration
1Entfernen Sie die Schutzkappe vom
Der ZyXEL
2Das
3Eine Warnmeldung erscheint. Klicken Sie auf Continue Anyway (Installation fortsetzen).
4Legen Sie die beigelegte CD in Ihr optisches Laufwerk ein. Wählen Sie Wechselmedien durchsuchen (Diskette, CD,...) und klicken anschließend auf Weiter.
5Klicken Sie nach dem erfolgreichen Installieren des Treibers auf Fertig stellen, um die Installation abzuschließen.
Einführung von OTIST
In einem drahtlosen Netzwerk müssen die drahtlosen Clients dieselben SSID- und Sicherheitseinstellungen haben wie der AP (Access Point) oder der drahtlose Router (im weiteren Textverlauf werden beide als AP bezeichnet), damit sie sich mit ihnen in Verbindung
setzen können. Früher mussten zunächst die Einstellungen am AP und dann genau dieselben Einstellungen manuell an jedem drahtlosen Client konfiguriert werden.
Mit der
erzeugt wird, wenn Sie keinen manuell konfiguriert haben.
OTIST aktivieren
Vor dem Übertragen der Einstellungen müssen Sie OTIST sowohl beim AP als auch beim drahtlosen Client aktivieren.
In dieser Bedienungsanleitung verwenden wir die Benutzeroberflächen des Prestige 334WT und
Der AP und die drahtlosen Klient(en) MÜSSEN denselben Setup Key (Schlüssel einrichten) verwenden.
AP
Sie können OTIST mit der
Halten Sie die
Wenn Sie jedoch zu lange auf die
Wechseln Sie im
Drahtloser Client
Starten Sie das
Starten von OTIST
Klicken Sie innerhalb von drei Minuten (beim Schreiben) im
1Im AP erscheint ein
2Dieses Fenster erscheint, während die OTIST- Einstellungen übertragen werden. Es wird wieder