Husqvarna YTH22V42 To USE Cruise Control J See Fig, To Adjust Mower Cutting Height See Fig

Page 10

OPERATION

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

K

J

L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

T

Fig. 8

•Put attachment lift lever in desired cutting height slot.

•Slide pointer tab (T) to desired cutting height as a reminder for next time you mow.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

•Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield

(S) in place (See Fig. 10).

S

Fig. 10

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual Manual de Operario English/SpanishGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Operate MowerTo Operate on Hills Service REMINDER/HOUR MeterReverse Operation System ROS To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigTransaxle Cooling EngineBelts Transaxle Pump FluidCleaning Deck Washout Port See Fig To Install Mower See Fig To Remove Mower See FigInstall belt on engine pulley M, in belt keepers G To Level Mower To Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Remove Wheel See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTransmission Engine OIL OtherFuel System CylindersTroubleshooting Problem Cause CorrectionEngine continues Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeFuncionamiento General Reglas DE SeguridadAdvertencia II. Funcionamiento EN PendientesServicio III. NiñosIV. Remolque Operaciones DE Servicio GeneralesEspecificaciones DEL Producto Identificación DE ProblemasTabla DE Materias Responsabilidades DEL ClienteDesempaque LA Caja DE Cartón Pedazos Para LA MontajeMontaje Verifique LA Batería Vea FigRevisión DE LA Posición Adecuada DE Todas LAS Correas Revisión DE LA Presión DE LAS LlantasRevisión DE LA Nivelación DEL CON- Junto Revisión DEL Sistema DE FrenosOperación Tractor y/o al motorDispositivo DE Aviso DE Servicio / Cronómetro Parada Vea Fig Como Usar SU TractorPara Ajustar EL Freno DE ESTACIONA- Miento Vea Fig Moversehaciaadelanteyhaciaatrás Vea FigCalibradoras Vea Fig Utilizar EL Mando Crucero Vea FigPara Ajustar LAS Ruedas Para Operar LA SegadoraPara Operar EN Cerros Para Parar LAS Cuchillas DE LA SegadoraFuncionamiento Atrás ROS Vea Fig Para Transportar Vea FigRevise EL Nivel DE Aceite DEL Motor Antes DE Hacer Arrancar EL MotorMecanismo DE Aviso DE Servicio / Cronómetro Agregue GasolinaPurgar LA Transmisión Calentamiento Para LA Transmision AutomaticaMantenimento Tabla DE LubricaciónOperación DEL Freno Cuidado DE LA CuchillaBatería LlantasEnfriamiento DEL Transeje CorreasLubricación Limpieza DE LA Rejilla DE Aire Filtro DE Aceite DEL MotorFiltro DEL Aire Sistema DE Enfriamiento DE AirePuerto DE Lavado DE LA Cubierta Vea Fig Servicio Y Ajustes Para Desmontar LA Cortadora DE Césped Vea FigConecte el fin de la primavera de cable de embrague Para Nivelar LA Segadora Regulación Visual DE Lado a Lado Vea FigPara Reemplazar LA Correa DE TRANS- Misión Vea Fig Remoción DE LA CorreaImpresión / Inclinación DE LAS Ruedas Delanteras Controlar Y Ajustar EL FrenoPara Hacer Arrancar EL Motor CON UNA Batería Baja Vea Fig Para Cambiar EL Fusible Para Cambiar LA Bombilla DE LA LUZ DelanteraEntrecierre Y Relés REMOCIÓN/REEMPLAZO DE LA TransmisiónMotor AlmacenamientoOtros Identificación DE Problemas Problema Causa CorrecciónIdentificación DE Problemas Pendiente 08/24/2011 CL
Related manuals
Manual 44 pages 20.69 Kb Manual 52 pages 16.58 Kb

YTH22V42 specifications

The Husqvarna YTH22V42 is a versatile and robust riding mower designed to meet the needs of homeowners looking for efficiency and durability in lawn care. This model is equipped with a powerful 22-horsepower Kohler engine, delivering reliable performance and enabling easy handling of various terrains. With its automatic transmission, operators can simply push a pedal to control the speed, providing a smooth and enjoyable mowing experience.

One of the standout features of the YTH22V42 is its 42-inch cutting deck, which allows for a wide cutting path, making it suitable for medium to large-sized yards. The cutting deck is reinforced, ensuring longevity and durability, while its air induction technology enhances airflow for a clean and even cut. The cutting height can be easily adjusted with a lever, offering six different settings from 1 to 4 inches.

Another significant characteristic of the YTH22V42 is its ease of use. The ergonomic design of the seat and steering wheel enhances comfort during longer mowing sessions. The mower is equipped with intuitive controls that make it easy for users of all experience levels to operate. Additionally, the unit features built-in anti-scalp wheels to protect the lawn from damage while trimming.

The Husqvarna YTH22V42 also boasts several innovative technologies. The ReadyStart system ensures an easy, no-prime starting of the engine, significantly reducing preparation time before mowing. The mower's compact design allows for easy maneuverability in tight spaces, making it effective for navigating around landscaping or garden features.

Furthermore, the YTH22V42 is compatible with Husqvarna’s extensive range of accessories, enhancing its versatility. From mulching kits to rear baggers, users can customize their mowing experience according to their specific lawn care needs.

In terms of maintenance, the YTH22V42 features a deck washout port, which simplifies cleaning under the cutting deck after use, prolonging the mower's lifespan and ensuring consistent performance. Additionally, the mower's robust construction ensures it can withstand the rigors of regular use.

Overall, the Husqvarna YTH22V42 combines power, comfort, and technology, making it an excellent choice for homeowners seeking a reliable and efficient riding mower. Its thoughtful design and advanced features position it as a leading option in the market, perfect for those looking to maintain a beautiful lawn with ease.
Top Page Image Contents